background image

 

 

SERVICE MANUAL 

PILOTLESS ELECTRONIC WATER HEATERS  

 

 

 
 

1.- NO IGNITION

 

No spark present. ...................................................................... 2

 

2.- NO IGNITION

 

Water Heater sparking but the burner does not ignite. ............................ 3

 

3.- THE  WATER FLOW IS VERY LOW ...................................................................... 3

 

4. CONTINUOUS SPARKING WHEN WATER HEATER IS IGNITED ...................................... 4

 

5.- SPARKING, BURNER IGNITES FOR A FEW SECONDS AND THEN SWITCHES OFF............... 4

 

6.- HARD IGNITION OF THE WATER HEATER  THERE IS NO SOFT START.......................... 5

 

7.- WATER HEATER CONTINUES SPARKING WHEN TAP IS TURNED OFF............................. 5

 

8.- WATER HEATER  SWITCHES OFF AFTER FEW MINUTES OF OPERATION ........................ 6

 

9.- WATER HEATER REMAINS IGNITED WHEN TAP IS  CLOSED ...................................... 7

 

10.- FLAMES IN BURNER ARE YELLOW ..................................................................... 7

 

11.- THE BATTERY LIFE IS VERY SHORT .................................................................. 8

 

12.- USEFUL DATA............................................................................................. 9

 

13.- IGNITION SEQUENCE ..................................................................................10

 

14.- PHOTO GALLERY .........................................................................................11

 

Summary of Contents for Nano Pro
















Reviews: