Electrolux EI30BM60M Installation Instructions Manual Download

Page: 1 / 24

Visit our Website at

READ CAREFULLY.

KEEP THESE INSTRUCTIONS

Installation

Over the Range

Instructions

Microwave Oven

Read these instructions completely and carefully.

•

IMPORTANT –

Save these

instructions for local inspector’s use.

•

IMPORTANT –

Observe all

governing codes and ordinances.

•

Note to Installer –

Be sure to leave these

instructions with the Consumer.

BEFORE YOU BEGIN

•

Note to Consumer –

Keep these

instructions for future reference.

•

Skill level

– Installation of this appliance requires

basic mechanical and electrical skills.

•

Proper installation is the responsibility of the installer.

•

Product failure due to improper installation is not
covered under the Warranty.

1-877-435-3287(US)

Questions? Call

1-800-265-8352(Canada)

p/n 316902904

April 2012

http://www.electroluxappliances.com

Summary of Contents for EI30BM60M

























Search results

Summary of Contents for EI30BM60M

Reviews:

Related manuals for EI30BM60M

Brands by name

Popular brands

Electrolux EI30BM60M, Installation Instructions Manual

Search results

Summary of Contents for EI30BM60M

Reviews:

Related manuals for EI30BM60M

Brands by name

Popular brands