background image

This document should only be removed by customer after installation.

P/N: 241540201

Not  satisfied with the installation of your refrigerator?

  

Z

Z

Z

Z

Z

 

Please contact the store you purchased it from.

Tu r n   t o   o t h e r   s i d e s   f o r

S p a n i sh   &   F r e n c h .

I n s t a l l a t i o n

Instructions

f o r

S i d e - B y - S i d e   R e f r i g e r a t o r

Prepare The Installation Site

Your counter-depth refrigerator is designed to be part of a built-in kitchen cabinet

system. Be sure to coordinate site preparation and installation with your kitchen

contractor.
Include these minimum guidelines in your site preparation:

• Choose a place near a grounded electrical outlet.
• Do not use an extension cord or an adapter plug.

• Avoid direct sunlight and close proximity to a range, dishwasher or other

heat source.

• Floor should be level and able to support a fully loaded refrigerator.
• The refrigerator’s Ice & Water Dispenser requires water supply access.

• Plan for easy access to counter tops when removing food.
• For complete access to drawers and freezer baskets, doors must be able to

fully open.

Allow the following clearances for ease of installation, proper air circulation, and

plumbing and electrical connections:
       

Sides & Top:

 3/8 inch         

Rear:

 1 inch

Transport Unpackaged Refrigerator To Site

By now, you have already removed your refrigerator’s shipping carton. You may

still need to use a hand truck to move it through close spaces or entrances. If the

refrigerator is larger than an entrance, consider two options:

• Remove the entrance door if one exists.

• Remove the refrigerator doors (see how in your 

Use & Care Guide

).

When using a hand truck:

• Load refrigerator from side of cabinet only.
• Do not run retaining straps over handles.

• Do not over-tighten retaining straps.
• Never use refrigerator handles to move the refrigerator.
• Remove tape from doors only after unit is in place.

Connect Water Supply

What you will need:

• Access to a cold water line

with pressure of

20-100 psi.

• Copper tubing with ¼-inch

(6.4mm) OD. Length for this

tubing is the distance from

the rear of the refrigerator to your household

water supply line 

plus

 7 feet (2.1 meters).

• A shut-off valve for the connection between your household

water line and the refrigerator supply line.

Do not

 use a self-piercing shut-off valve.

• A compression nut and ferrule (sleeve) for the water supply

connection at the rear of your refrigerator.

2

3

To connect the water supply to the rear of your refrigerator:

1

Ensure that the refrigerator is not plugged in.

2

Flush the supply line until water is clear by placing the end of the

copper tube in a sink or bucket and opening the shut-off valve.

3

Unscrew the plastic cap from the water valve inlet at the rear of

your refrigerator. Discard the cap.

4

Slide the brass compression nut, then the ferrule (sleeve) onto

copper tube.

5

Push the copper tube into water valve inlet as far as it will go

(1/4 inch).

6

Slide the ferrule (sleeve) into valve and finger-tighten the

compression nut onto valve. Tighten another half turn with a

wrench. 

Do not over-tighten

.

7

Secure the copper tube to your refrigerator’s rear panel with a

steel clamp and screw (see illustration).

8

Coil the excess copper tubing (about 2½ turns) behind your

refrigerator as shown. Arrange coiled tubing to avoid vibration or

wear against other surfaces.

9

Open water supply shut-off valve and tighten any connections

that leak.

Place In Permanent Position

If possible, use a hand truck to position the refrigerator directly in front of

its cabinet enclosure.
Be careful not to move the refrigerator beyond its water supply (copper

tubing) connections.
Plug in the power cord, and push the refrigerator straight back into

place.

Level Refrigerator & Adjust Doors 

(if necessary)

Guidelines for final positioning of your refrigerator:

• All four corners of the cabinet must rest firmly

on the floor.

• The cabinet should be level at the front and rear.

• The sides should tilt ¼-inch (6 mm) from front to back

(to ensure that doors close and seal properly).

• Doors should align with each other and be level.

All of these conditions can be met by raising or lowering the

adjustable front rollers.

To adjust the front rollers:

1

Open both doors and remove the toe grille by

unscrewing its two mounting screws and gently pulling

forward (see illustration).

2

Close the doors and use a flat-blade screwdriver or 3/

8-inch socket wrench to raise or lower the front rollers.

3

Ensure both doors are bind-free with their seals

touching the cabinet on all four sides.

4

Replace the toe grille by fitting it into place and

refastening its mounting screws.

5

Remove Internal Shipping Materials

Electrolux uses packing foam and tape to secure the internal parts of your refrigerator for shipping. Once the

refrigerator is in position, you can remove this material.

Check Initial System Settings

Your refrigerator includes an ice &

water dispensing system, a digital

temperature control system,

controls to monitor the status of a

water filter, and controls for storage

drawer humidity and temperature.
See the 

Use & Care Guide

 to

learn more about the start-up

settings for these controls.

Problems? Try These Suggestions

Operation problems are possible if any of the installation tasks are not completed. Here is a list of things to check

for:

• Is the refrigerator’s power cord plugged in?
• Is the refrigerator connected to the household water supply?
• If you had to remove the refrigerator and freezer doors, did you reattach water and power connectors at the

door hinges? (See the 

Use & Care Guide

 for detailed instructions on removing and replacing doors.)

• Is the ice maker power switch turned 

On

?

Other possibilities to check:

• Is the power to the receptacle turned on?

• Is the water filter above the fresh food compartment fully seated (see 

Use & Care Guide

 for details)?

If you still have operation problems after checking these suggestions, please see the “Solutions To Common

Problems” section in your 

Use & Care Guide

.

What’s Next?

Congratulations. You are ready to begin enjoying your new Electrolux refrigerator.

• To become aware of important safety instructions and learn how to operate your refrigerator, please read the

entire 

Use & Care Guide

.

• You may want to start with the “Normal Operating Sights & Sounds” section of the 

Guide

 to learn more about

what to expect during typical operation.

• Please register your product. You can use the CD that came with your refrigerator to register online, or you

can simply send in the Registration Card.

And thank you for choosing Electrolux.

7

8

9

1

NO

NO

NO

NO

NOTE

TE

TE

TE

TE

These installation

instructions are provided

only as a possible customer

option. Electrolux

recommends that you use a

service or kitchen

contracting professional to

install your refrigerator.

!

WARNING

WARNING

WARNING

WARNING

WARNING

To avoid electric shock, which can cause death or severe personal injury, do not connect your

refrigerator to an electrical power source until you have completed Step 3 of these instructions.

NO

NO

NO

NO

NOTE

TE

TE

TE

TE

Information about

cabinetry construction for

Electrolux products is

available for contractors.

Call 1-877-435-3287.

!

CA

CA

CA

CA

CAUTION

UTION

UTION

UTION

UTION

Room temperatures below

55°F (13°C) or above

110°F (43°C) will impair

cooling ability of your

refrigerator’s compressor.

!

CA

CA

CA

CA

CAUTION

UTION

UTION

UTION

UTION

Shifting the refrigerator from side to side

may damage flooring.

NO

NO

NO

NO

NOTE

TE

TE

TE

TE

Electrolux Kit #53039117950, available from

your dealer, provides all materials for a water

supply installation, including 25 feet of

copper tubing and full instructions.

NO

NO

NO

NO

NOTES

TES

TES

TES

TES

• The ice maker’s fill valve may operate noisily if the household water supply is shut off.

• After ensuring no water leaks exist at any connection, be sure to check for leaks again in 24 hours.
• See your 

Use & Care Guide

 for detailed information about setting up and operating the Ice & Water

Dispensing system.

4

!

CA

CA

CA

CA

CAUTION

UTION

UTION

UTION

UTION

• Shifting the refrigerator from

side to side may damage

flooring.

• Do not block the toe grille on

the lower front of your

refrigerator. Sufficient air

circulation is essential for

proper operation.

IMPOR

IMPOR

IMPOR

IMPOR

IMPORT

T

T

T

TANT

ANT

ANT

ANT

ANT

If you are installing your refrigerator without connecting it to a water

supply, make sure the ice maker’s power switch is turned 

Off

 (see the

Use & Care Guide

 for more details).

NO

NO

NO

NO

NOTE

TE

TE

TE

TE

The doors are designed to close automatically at

an opening of 20 degrees or less.

6

NO

NO

NO

NO

NOTE

TE

TE

TE

TE

After changing control settings,

wait 24 hours before making

further adjustments.

Adjustable

Wrench

Socket

Wrench Set

OR

Phillips Head

Tools Necessary:

3/8” Fixed

Wrench

AND

OR

eçìëÉ

éäìãÄáåÖ

äáåÉ

t~íÉêäáåÉ=Üççâìé

_

íÜÉ ï

!

CA

CA

CA

CA

CAUTION

UTION

UTION

UTION

UTION

To avoid property damage:

• Use copper tubing for the water

supply line (plastic tubing is more

likely to leak).

• Ensure water supply complies with

local plumbing codes.

Digital
Control
Panel

NO

NO

NO

NO

NOTE

TE

TE

TE

TE

Location of these

materials may vary

depending on your

model.

Reviews: