Electrohome VistaGRAPHX 2500 User Manual Download

Page: 1 / 101

User's Manual

Table of Contents

54-007079-03P (10/98) Software Version 2.1

VistaGRAPHX 2500 User's Manual

iii

Section

Contents

Page

1.1

The Projector ....................................................................................................1-1

1.2

Components ......................................................................................................1-2

1.3

Purchase Record and Servicing.........................................................................1-2

2.1

Quick Setup ......................................................................................................2-1

2.2

Installation Considerations................................................................................2-2

2.3

Projector Position and Mounting ......................................................................2-6

2.4

Source Connections ..........................................................................................2-9

2.5

Power Connection...........................................................................................2-12

2.6

Operating Orientation .....................................................................................2-13

2.7

Leveling ..........................................................................................................2-13

2.8

Zoom, Focus & Vertical Offset.......................................................................2-14

2.9

Serial Port Connections ..................................................................................2-14

2.10

Keypad Protocols............................................................................................2-17

3.1

Overview...........................................................................................................3-1

3.2

Projector Basics ................................................................................................3-1

3.3

Using the Keypads ............................................................................................3-3

3.4

Navigating the Menus .......................................................................................3-9

3.5

Using Sources and Channels...........................................................................3-13

3.6

Adjusting the Image ........................................................................................3-17

3.7

Adjusting and Checking System Parameters...................................................3-28

3.8

Using Multiple Projectors ...............................................................................3-33

3.9

Error Conditions .............................................................................................3-34

4.1

Warnings and Guidelines ..................................................................................4-1

4.2

Cleaning ............................................................................................................4-3

4.3

Replacing Keypad Batteries..............................................................................4-3

4.4

Replacing the Lamp and Filter..........................................................................4-4

4.5

Replacing the Lens............................................................................................4-8

4.6

Troubleshooting ................................................................................................4-8

5.1

Specifications....................................................................................................5-1

Glossary ........................................................................................................... A-1

Keypad Reference ........................................................................................... B-1

Menu Tree........................................................................................................ C-1

Serial Communication Cables.......................................................................... D-1

Throw Distance................................................................................................ E-1

Optional Input Modules ....................................................................................F-1

NOTE: Due to constant research, the information in this manual is subject to change without notice

Introduction

Installation &

Setup

Operation

Maintenance

Specifications

Appendices

Summary of Contents for VistaGRAPHX 2500






































































































Search results

Summary of Contents for VistaGRAPHX 2500

Reviews:

Related manuals for VistaGRAPHX 2500

Brands by name

Popular brands

Electrohome VistaGRAPHX 2500, User Manual

Search results

Summary of Contents for VistaGRAPHX 2500

Reviews:

Related manuals for VistaGRAPHX 2500

Brands by name

Popular brands