background image

REV I – 3/1/2016 

INSTALLATION INSTRUCTIONS & HOME OWNERS MANUAL 

AUTOBOOSTER™ 

IMPORTANT SAFETY INFORMATION 

When installing or using any high voltage electrical appliance, basic safety precautions should always be 

followed. Under no circumstance should you attempt to clean, install, inspect, repair, disassemble or 

otherwise service this water heater, without first shutting off 

all

 power to the unit directly at the circuit 

breaker box. 

SERIOUS BODILY INJURY OR DEATH COULD OCCUR IF YOU IGNORE THIS WARNING. 

IF ASSISTANCE IS NEEDED, A LICENSED AND QUALIFIED PLUMBER AND ELECTRICIAN IN ACCORDANCE 

WITH ALL APPLICABLE NATIONAL, STATE, PROVINCIAL, AND LOCAL PLUMBING AND ELECTRICAL CODES 

SHOULD BE HIRED. 
PLEASE READ THESE INSTRUCTIONS THOROUGHLY AND COMPLETELY PRIOR TO INSTALLATION & USE. 

FAILURE TO DO SO COULD CAUSE PROPERTY DAMAGE, SERIOUS INJURY, OR DEATH. 

This manual should be shown to all members of the household who plan to use this unit, and be retained for 

future reference.

 

Tested and certified by the Water Quality Association against NSF/ANSI 372 for lead free 

compliance. 

Downloaded from https://gadgetsgo.com/AutoBooster-HATB007240-water-tank-heater-boost.html Authorized Eemax Dealer

Summary of Contents for AUTOBOOSTER





















Reviews: