ACCESSORIES
1
2
3
4
5
Push Button ( 100% Power----> 50% Power -------> 30%+Sensor 100% -----> OFF)
1
2
USB 5V 1A Output. ( To charge mobile or other device.)
4
DC input for charge connector for solar panel 6V input. (Warning : Do not use other device or solar panel to charge.
）
5
Motion Sensor ( Two options on remote, 0% + 100% for 24 hours, 30% +100 for 12 hours )
6
6
Wall Switch for extension control. Same function as push button .
1
3
DC input connector to connect to plug to wall switch.
6
CONNECTION DIAGRAM
Wall Switch Control
4M Switch cable
5M Charge cable
USB Charge
Remote Control
USER MANUAL
Solar LED Batten Light Kits
Version : A20181106
100% Green
Energy
Rechargeable
Lithium Battery
PIR Motion
Sensor
IP65 Rated
Waterproof
5V USB
Charge
Integrated
Design
Bugs
Free
Non contractual photo
Solar led batten light is the pioneer model comparing with the normal solar powered tube light, widely used in many
applications, such as office, home, garage, caravan, carports, bus stations, warehouses, camping tents, kinds of shelves,
farm tents, sideways, emergency camps, aid tents, temporary or permanent caves, or any kinds of sheds of paths, etc.
Solar led batten light is a kit that contains everything, like rechargeable lithium battery, solar controller, solar panel. Easy
installation in less than 15 minutes, you just need to plug solar panel into the light by DC connector. It provides a high
brighttness for long time continuous lighting output, and inbuilt PIR sensor can save power if sunshine is not strong
enough.
This solar led batten light is also supported to work during day time while being charged, under manual operation. By
programming the remote control, you can increase or decrease the brightness as you like, there are 2 hours, 4 hours
and 6 hours for optional. Pressing the button on light, you will find out 3 lighting modes , brightness and time can be
set easily by remote control.
One 5V USB output was added to charge your mobile, What's more , an external switch is allowed to be connected to
this light via a DC port. The ON/OFF and brightness can be operated by hand just like the traditional lights. This is a
very useful advantage for the applications which need to do the lighting operation by hand instead of automatic.
It is a perfect lighting solution for the remote area where is lack of power and lighting.
WHAT IS IT?
SPECIFICATION
Size
LED Max
Max lumen
Solar Panel
Battery
Cable
360mm
12W
1200lm
10W 6V
3.7V 12AH
5.0 M
600mm
24W
2400lm
18W 6V
3.7V 24AH
5.0 M
IP Rate
IP65
IP65
Solar Batten Light
Solar Panel + 5m cable + 2 brackets
Wall Cont 4 m cable
Remote Control
Fixing dowels and SST304 screws.
User Manual
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1. ON / OFF mode Night & Day (works manually day and night)
2. 130 degree motion detection area.
3. Manual dimmer mode
4. Timer mode : Turns ON/OFF automatically after 2H, 4H or 6H.
5. Automatic Mode: Working from dusk to dawn automatically.
CONTENT OF PACKAGING:
ADVANTAGES
WALL SWITCH
MANUAL
switch ON/OFF , 100% full power
AUTOMATIC
ON/OFF up dawn & dark , 100% full power
Increase the brightness by 20%
Decrease the brightness by 20%
Light is 0% (off power)
turn ON when sensor is triggered.
Light is ON with 30% power,
and 100% when sensor is triggered.
Set light to work for 2 hours
Set light to work for 4 hours
Set light to work for 6 hours
REMOTE CONTROL
Wall Switch is a very useful components in this kit, You can use
this wonderful solar light fixture in the same way of using a 220V
normal light.
1st push : 100% Power
2nd push : 50% Power
3nd push : 30% when nobody there and go to 100% power
when sensor is triggered
4th push : Light Off.
( These 4 working programs are looped. )
INSTALLATION
1. Drill the hole for screws
Screw diameter is 4mm
1
2
2. Insert the screw cap into wall
and make it flat as surface
4
4. Connect light and solar panel
by the DC solar cable.
5
3. Use screw driver to fix
the screws into the wall/ceiling
3
6. Select AUTO or MANUAL mode and
set the lighting program as you like
6
1. When installation is completed, The batten light will start to work under automatic mode as default setting..
2. There is manual mode optional which support light to work at day time. Under manual mode,
light will turn off after 12 hours if not turn off by hand.
3. When the red light flashes one time when you try to turn it on,
it means there is no power in battery, please try to charge the light well.
Remark
5. Press button to turn on light, 1st push
: 100% power . 2nd : 50% Power . 3rd
push
:
30%+ 100% when sensor is
triggered. 4th push : OFF
HOW TO REPLACE BATTERY
2
1
5
4
8
7
2 : Use clips or small tools to take
out the two silicone plugs.
1. Remove the bracket from the
side where there are no buttons
3 : Use 3mm Inner hexagon spanner
to loose and remove the two screws.
4 : Seperate the end cap from tube
body. ( Please do not lost the
waterproo silicon ring.)
5 : Hold the battery cable and take it
out carefully from light fixture
until you see the DC connectors
6 : Disconnect the DC connectors
then take out the battery carefully.
7 : Hold the cable connector from light,
and insert battery properly, then
connect battery cable to light cable
by DC connectors
8 : Put the end cap back to tube body
with silicon wing at good position.
9 : Repeat the steps of last operations
6-->5-->4-->3-->2-->1.
Tip :
When new battery is connected to controller sucessfully, the red light inside of motion sensor will start ON for 2 seconds, then off.
Solar LED Lithium Light Kit
