background image

CS-500ES

01-50D-01

1

INTRODUCTION

We are constantly working on technical im-
provement of our products. For this reason, 
technical data, equipment and design are 
subject to change without notice. All speci-
fications and directions in this SERVICE 
DATA are based on the latest product infor-
mation available at the time of publication.

SERVICE DATA

CHAIN SAW

ECHO:

 CS-500ES

STAGE    MODEL

(Serial number : 37000001 and after)

0

CONTENTS

 

page

1 SERVICE INFORMATION

 .............................. 2

1-1 Speci

fi

 cation ............................................... 2 

1-2 Technical data ............................................. 3
1-3 Torque limits................................................ 4
1-4  Special repairing materials ......................... 4
1-5 Service limits............................................... 5
1-6 Special tools ............................................... 6

2 CARBURETTOR ADJUSTMENT PROCEDURE

 .. 7

2-1  General adjusting rules ............................... 7
2-2  Presetting Idle adjust screw, L mixture needle 
and H mixture needle ........................................ 7
2-3 Adjusting carburettor................................... 8

3 SERVICE HINT for PET-9000

 ........................ 8

Reference No.

 

01-50D-01

R E V I S E D :     2 0 1 2 0 1

ISSUED: 201106

Summary of Contents for CS-500ES









Reviews: