E-flight Blade SR RTF Airframe Instruction Manual Download

Page: 1 / 38

RTF

4105 Fieldstone Road

Champaign, IL 61822

USA

Horizon Hobby UK

Units 1-4 Ployters Rd

Staple Tye

Harlow, Essex

CM18 7NS

United Kingdom

Horizon Hobby Deutschland GmbH

Hamburger Strasse 10

25335 Elmshorn

Germany

E-flite

products are distributed exclusively by Horizon Hobby, Inc.

US Patent 7,391,320. Other Patents Pending

DSM and DSM2 are trademarks or registered trademarks of Horizon Hobby, Inc.

The Spektrum trademark is used with permission of Bachmann Industries, Inc.

Spektrum radios and accessories are exclusively available from Horizon Hobby, Inc.

Printed 11/09

www.E-fliteRC.com

16165

Specifications

Length . . . . . . . . . . . . . . . . . . . . . 19.10 in (485mm)

Height . . . . . . . . . . . . . . . . . . . . . 6.90 in (176mm)

Main Rotor Diameter . . . . . . . . . . . 21.80 in (552mm)

Tail Rotor Diameter . . . . . . . . . . . . 3.20 in (82mm)

Weight with Battery . . . . . . . . . . . . 120 oz (340 g)

Main Motor . . . . . . . . . . . . . . . . . . Brushless 3900Kv (installed)

Tail Motor . . . . . . . . . . . . . . . . . . . Direct-Drive N60 (installed)

Battery . . . . . . . . . . . . . . . . . . . . . 3S 11.1V 1000mAh Li-Po (included)

Charger . . . . . . . . . . . . . . . . . . . . 3-Cell 11.1V Li-Po

Power Supply . . . . . . . . . . . . . . . . AC to 12V DC, 1.5A (included)

Transmitter . . . . . . . . . . . . . . . . . . HP6DSM 2.4GHz DSM 6-channel (included)*

Receiver . . . . . . . . . . . . . . . . . . . . Spektrum AR6110e 2.4GHz DSM Microlite (installed)

On-Board Electronics . . . . . . . . . . . 2-in-1 Mixer/ESCs (installed)

Servos . . . . . . . . . . . . . . . . . . . . . DS75 Digital Sub-Micro (3 installed)

Gyro . . . . . . . . . . . . . . . . . . . . . . . G110 Micro Heading Lock (installed)

* CCPM Helicopter programming is specific to Blade SR. Please do not attempt to use transmitter with

any other CCPM helicopter

Summary of Contents for Blade SR RTF Airframe







































Search results

Summary of Contents for Blade SR RTF Airframe

Reviews:

Related manuals for Blade SR RTF Airframe

Brands by name

Popular brands

E-flight Blade SR RTF Airframe, Instruction Manual

Search results

Summary of Contents for Blade SR RTF Airframe

Reviews:

Related manuals for Blade SR RTF Airframe

Brands by name

Popular brands