Passport
™
Duo 400W Dual AC/DC Touch Charger
Instruction Manual | Bedienungsanleitung | Manuel d’utilisation | Manuale di Istruzioni
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit
horizonhobby.com and click on the support tab for this product.
MEANINg Of SPECIAl lANguAgE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE:
Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
CAUTION:
Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
WARNING:
Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of
superficial injury.
WARNING:
Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly
can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product
in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult
supervision. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, LLC. This manual
contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or
use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
INCluDED ITEMS
(2) Banana plug to EC3™ battery connector (DYNC0066)
AC power cord (one region—US, EU, AU or UK)
(2) JST_XH balance adapter (DYN5032)
OPTIONAl ITEMS
DC power cord (DYNC1103)
Banana to Traxxas® insulated charge adapter: male (DYNC0054)
Charger lead with receiver connector (DYNC0033)
Banana to Deans insulated charge adapter: male (DYNC0053)
LiPo Charge Protection Bag, Small (DYN1400)
LiPo Charge Protection Bag, Large (DYN1405)
Temperature Sensor (DYN5033)
SPECIfICATIONS
Input Voltage 100-240V AC; 11-18V DC
Charging Capability 1–6S Li-Po/Li-Ion/Li-Fe;
1–10C Ni-Cd/Ni-MH; 2–24V Pb
Battery Capacities 50–10000 mAh
Charge Current 0.01–10.0A (in 0.1A increments/200W max per channel)
Discharge Current 0.01–5A (in 0.1A increments/200W max per channel)
Operating Temperature 0ºC to + 40ºC
Charging Mode Ni-Cd/Ni-MH: Peak; Li-Po/Li-Ion/Li-Fe/Pb: CC/CV
Protection Short-circuit, over-current, reverse polarity, low input
voltage, over-temperature
NOTICE:
This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for their safety.
ChArgINg WArNINgS
WARNING:
Failure to exercise caution while using this product and
comply with the following warnings could result in product malfunction,
electrical issues, excessive heat, FIRE, and ultimately injury and property
damage.
• NEVER LEAVE ChARGING bATTERIEs UNATTENDED.
• NEVER ChARGE bATTERIEs OVERNIGhT.
• Never attempt to charge dead, damaged or wet battery packs.
• Never attempt to charge a battery pack containing different types of batteries.
• Never allow children under 14 years of age to charge battery packs.
• Never charge batteries in extremely hot or cold places or place in direct
sunlight.
• Never charge a battery if the cable has been pinched or shorted.
• Never connect the charger if the power cable has been pinched or shorted.
• Never connect the charger to an automobile 12V battery while the vehicle is
running.
• Never attempt to dismantle the charger or use a damaged charger.
• Never attach your charger to both an AC and a DC power source at the same
time.
• Never connect the input jack (DC input) to AC power.
• Always use only rechargeable batteries designed for use with this type of
charger.
• Always inspect the battery before charging.
• Always keep the battery away from any material that could be affected by
heat.
• Always monitor the charging area and have a fire extinguisher available at all
times.
• Always end the charging process if the battery becomes hot to the touch or
starts to change form (swell) during the charge process.
• Always connect the charge cable to the charger first, then connect the battery
to avoid short circuit between the charge leads. Reverse the sequence when
disconnecting.
• Always connect the positive red leads (+) and negative black leads (–) correctly.
• Always disconnect the battery after charging, and let the charger cool between
charges.
• Always charge in a well-ventilated area.
• Always terminate all processes and contact Horizon Hobby if the product
malfunctions.
WARNING:
Never leave charger unattended, exceed maximum charge
rate, charge with non-approved batteries or charge batteries in the wrong
mode. Failure to comply may result in excessive heat, fire and serious
injury.
CAUTION:
Always ensure the battery you are charging meets the
specifications of this charger and that the charger settings are correct.
Not doing so can result in excessive heat and other related product
malfunctions, which can lead to user injury or property damage. Please
contact Horizon Hobby or an authorized retailer with compatibility
questions.
gETTINg STArTED
Using an AC Power source:
1. Ensure the charger is powered OFF.
2. Connect the AC power cord
(D)
to the AC power source.
3. Power ON the charger with the Power Switch
(A)
.
4. When the charger is powered ON, a message will appear on the
LCD Touch
screens (E,F)
.
Using a DC Power source:
1.
Connect the DC power cord to the charger DC Power Input Port
(C)
2.
Connect the DC alligator clips to the DC power source.
3.
Power ON the charger with the Power Switch
(A)
.
4.
When the charger is powered ON, a message will appear on the
LCD Touch
screens (E,F)
.
Connecting the battery to the Charger:
CAUTION:
Always power ON the charger before connecting a battery, or
damage to the charger and the battery can result.
1.
With charger powered on, select charging settings.
2.
Connect the battery to the charger.
3.
Start battery charging.
CAUTION:
Before charging, always ensure you have chosen the correct
battery chemistry type for the battery you are charging.
PrOgrAMMINg quICk guIDE
1. Press the
Left
and
Right Arrows
on the
LCD Touch screen
to scroll through
the main menu screens.
2. Press the action at the bottom of the
LCD Touch screen
to enter that menu.
3. Press a parameter to highlight that parameter.
4. Press the
Up
and
Down Arrows
to edit the parameter.
5. Press
select
to save the parameter.
6. If there is more than one screen of parameters, press the top right corner of the
LCD Touch screen
to scroll through the parameter screens.
7. Press
back
to return to the main menu screens.
When the charger is powered ON, there is a series of self tests and the screen will
show the charger brand name and model number.
D Y N C 3 0 0 5
USER_NAME
OPErATINg YOur ChArgEr
CAUTION:
If at any time during the charge process the battery pack becomes hot or begins to puff disconnect the battery immediately and discontinue the
charge process as batteries can cause fire, collateral damage and injuries.
CAUTION:
Using a charge rate that is not compatible with the battery capacity may result in damage or malfunction of the charger or battery.
CAUTION:
The Lithium charge program menus are to be used ONLY for the charging and discharging of Lithium battery packs. Charging other battery types
using the Lithium charge programs will damage the battery or the charger.
1 - SElf TEST AND PrOgrAM SElECT SCrEENS
1. Connect the JST_XH balance adapter to the
balance Circuit Adapter board
Connector (6)
.
2. Connect the battery connector to the device connector.
3. Connect the balance connector of the battery to the JST_XH balance adapter.
4. Press the
Left
and
Right Arrows
on the
LCD Touch screen
to scroll through
the main menu screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe/Li-HV.
Program select=LiPo
LiPo
CHG
DCHG
STOR
5. Press
ChG
.
LiPo CHARGE
Pack.Volt. : 11.1V/3S
Capacity : 2100mAh
Current : 2.1A
End Cell Volt :
4.20V
Press&Hold : CHARGE
BACK
SELECT
6. Press a parameter to highlight that parameter.
7. Press the
Up
and
Down Arrows
to edit the parameter.
8. Press
select
to save the parameter.
9. Once the parameters are at the desired settings, press and hold
ChARGE
.
10. The charger will check the battery and charger settings and charging will begin.
The charger will beep and display the following screen:
LiPo CHG
000:11S
Capacity : 11mAh
Current : 4.0A
Voltage : 8.00V
Resistance :
392mΩ
Peak Temp.
:
No sens
STOP
Unit
Graph
11. Press the
arrow
in the top right of the
LCD Touch screen
to see the rest of
the Charging information.
12. Press
Unit
to see the voltages for each cell. Press
back
to return to the
charging screen.
13. Press
REs.
to see the cell resistance screen. Press
back
to return to the
voltage screen.
14. Press
Graph
to see the battery voltage graph. Press
back
to return to the
charging screen.
Data LiPo = Graph
8.03V 000:34S
BACK
15. Press
sTOP
at any time to stop charging.
16. When charging is complete, the charger will sound a series of beeps and
display the following screen:
17. Press the
arrow
in the top right of the
LCD Touch screen
to see the rest of
the Charging information.
18. Disconnect the battery from the charger.
2 - lIThIuM (lI-PO/lI-fE/lI-ION/lI-hV) ChArgINg
3 - lIThIuM DISChArgINg
2A- lIThIuM hIgh VOlTAgE
1.
Connect the JST_XH balance adapter to the
balance Circuit Adapter
board Connector (6)
.
2.
Connect the battery connector to the device connector.
3.
Connect the balance connector of the battery to the JST_XH balance adapter.
4.
Press the
Left
and
Right Arrows
on the
LCD Touch screen
to scroll
through the main menu screens until you reach Program Select=Li-Po/Li-Ion/
Li-Fe/Li-HV.
5. Press
DChG
.
6. Press a parameter to highlight that parameter.
7. Press the
Up
and
Down Arrows
to edit the parameter.
8. Press
select
to save the parameter.
9. Once the parameters are at the desired settings, press and hold
DIsChRG
.
10. The charger will check the battery and charger settings and discharging will
begin. The charger will beep and display the following screen:
11. Press the
arrow
in the top right of the
LCD Touch screen
to see the rest of
the Discharging information.
12. Press
Unit
to see the voltages for each cell. Press
back
to return to the
discharging screen.
13. Press
REs.
to see the cell resistance screen. Press
back
to return to the
voltage screen.
14. Press
Graph
to see the battery voltage graph. Press
back
to return to the
discharging screen.
15. Press
sTOP
at any time to stop discharging.
16. When discharging is complete, the charger will sound a series of beeps and
display the following screen:
17. Press the
arrow
in the top right of the
LCD Touch screen
to see the rest of
the Charging information.
18. Disconnect the battery from the charger.
4 - lIThIuM STOrAgE ChArgINg
1.
Connect the JST_XH balance adapter to the
balance Circuit Adapter
board Connector (6)
.
2.
Connect the battery connector to the device connector.
3.
Connect the balance connector of the battery to the JST_XH balance adapter.
4.
Press the
Left
and
Right Arrows
on the
LCD Touch screen
to scroll
through the main menu screens until you reach Program Select=Li-Po/Li-Ion/
Li-Fe/Li-HV.
5. Press
sTOR
.
6. Press a parameter to highlight that parameter.
7. Press the
Up
and
Down Arrows
to edit the parameter.
8. Press
select
to save the parameter.
9. Once the parameters are at the desired settings, press and hold
sTORE
.
10. The charger will check the battery and charger settings and storage charging
will begin. The charger will beep and display the following screen:
11. Press the
arrow
in the top right of the
LCD Touch screen
to see the rest of
the storage Charging information.
12. Press
Unit
to see the voltages for each cell. Press
back
to return to the
storage charging screen.
13. Press
Graph
to see the battery voltage graph. Press
back
to return to the
storage charging screen.
14. Press
sTOP
at any time to stop charging.
15. When charging is complete, the charger will sound a series of beeps and
display the following screen:
16. Press the
arrow
in the top right of the
LCD Touch screen
to see the rest of
the Charging information.
17. Disconnect the battery from the charger.
CAUTION:
The nickel charge program menus are to be used ONLY for the charging and discharging of nickel battery packs. Charging other battery types using
the nickel charge programs will damage the battery or the charger.
1. Connect the battery connector to the device connector.
2. Press the
Left
and
Right Arrows
on the
LCD Touch screen
to scroll through
the main menu screens until you reach Program Select=Ni-MH/Ni-Cd.
Program select=NiMH
CHG
DCHG
N i M H
CYCLE
3. Press
ChG
.
NiMH CHARGE
Capacity : 50mAh
Current : 0.1A
CHG Mode
:
Man
Delta Peak
:
5m V/C
Press&Hold : CHARGE
BACK
SELECT
4. Press a parameter to highlight that parameter.
5. Press the
Up
and
Down Arrows
to edit the parameter.
6. Press
select
to save the parameter.
7. Once the parameters are at the desired settings, press and hold
ChARGE
.
8. The charger will check the battery and charger settings and charging will begin.
The charger will beep and display the following screen:
NiMH CHG
000:09S
Capacity : 2mAh
Current : 1.8A
Voltage : 7.98V
Resistance : ****mΩ
Peak Temp.
:
No sens
STOP
Graph
9. Press the
arrow
in the top right of the
LCD Touch screen
to see the rest of
the Charging information.
10. Press
Graph
to see the battery voltage graph. Press
back
to return to the
charging screen.
Data NiMH = Graph
8.03V 000:28S
BACK
11. Press
sTOP
at any time to stop charging.
12. When charging is complete, the charger will sound a series of beeps and
display the following screen:
13. Press the
arrow
in the top right of the
LCD Touch screen
to see the rest of
the Charging information.
14. Disconnect the battery from the charger.
Only Li-Po is shown in the following three sections. Li-Ion/Li-Fe/Li-hV menus differ ONLY in Cell and Pack Voltage values.
Only Ni-Mh is shown in the following three sections.
TABlE Of CONTENTS
1 -
Self Test and Program Select Screens
2 -
Lithium (Li-Po/Li-Fe/Li-Ion/Li-HV) Charging
2A -
Lithium High Voltage
3 -
Lithium (Li-Po/Li-Fe/Li-Ion/Li-HV) Discharging
4 -
Lithium (Li-Po/Li-Fe/Li-Ion/Li-HV) Storage Charging
5 -
Nickel (Ni-MH/Ni-Cd) Charging
6 -
Nickel Discharging
7 -
Nickel Cycle Charging
8 -
Pb Charging
9 -
Pb Discharging
10 -
Setup
11 -
View
12 -
Balance
13 -
Memory
14 -
USB Device Charging
15 -
Troubleshooting
5 - NICkEl (NI-Mh/NI-CD) ChArgINg
VOlTAgE MuST BE SET TO ThE COrrECT VAluE BEfOrE ThE ChArgEr IS POWErED ON.
DATA LiPo–CELLS
BACK RES.
4.08 4.07 4.06 0.00 0.00 0.00
1> 114MΩ
2> 104MΩ
3> 100MΩ
4> -- MΩ
Main:320MΩ
– Resistance –
5>
-- MΩ
6> -- MΩ
7> -- MΩ
8> -- MΩ
BACK
LiPo CHG
010:30S
Input Volt
:
12.22V
End Volt.
:
12.60V
Int Temp
:
21ºC
Safety Timer :
240min
Capacity Lim :
2100mAh
STOP
Unit
Graph
LiPo DONE
010:30S
Input Volt
:
12.22V
End Volt.
:
12.60V
Int Temp
:
21ºC
Safety Timer :
240min
Capacity Lim :
2100mAh
STOP
Unit
Graph
NiMH DONE
001:15S
Input Volt
:
14.8?V
Delta Peak
:
8mV/C
Int Temp.
:
60F
Safety Timer :
240min
Capacity Lim. :
3300mAh
BACK
Cycle
Graph
LiPo DCHG
000:30S
Capacity : 13mAh
Current : 1.4A
Voltage : 11.39V
Resistance :
369mΩ
Peak Temp.
:
No sens
STOP
Unit
Graph
LiPo DONE
000:30S
Input Volt
:
12.25V
End Volt.
:
11.40V
Int Temp
:
20ºC
Safety Timer :
240min
Capacity Lim :
2100mAh
STOP
Unit
Graph
LiPo DONE
000:30S
Capacity : 13mAh
Current : 1.4A
Voltage : 11.39V
Resistance :
369mΩ
Peak Temp.
:
No sens
STOP
Unit
Graph
LiPo DONE
010:30S
Input Volt
:
12.22V
End Volt.
:
12.60V
Int Temp
:
21ºC
Safety Timer :
240min
Capacity Lim :
2100mAh
STOP
Unit
Graph
LiPo STORE
010:30S
Input Volt
:
12.22V
End Volt.
:
12.60V
Int Temp
:
21ºC
Safety Timer :
240min
Capacity Lim :
2100mAh
STOP
Unit
Graph
LiPo DONE
010:30S
Input Volt
:
12.22V
End Volt.
:
12.60V
Int Temp
:
21ºC
Safety Timer :
240min
Capacity Lim :
2100mAh
STOP
Unit
Graph
Program select=LiPo
LiPo
CHG
DCHG
STOR
LiPo DISCHARGE
Pack.Volt. : 11.1V/3S
Capacity : 2100mAh
Current : 2.1A
End Cell Volt :
3.80V
Press&Hold : DISCHRG
BACK
SELECT
DATA LiPo–CELLS
BACK RES.
3.80 3.80 3.80 0.00 0.00 0.00
Data LiPo = Graph
7.91V 001:25S
BACK
1> 114MΩ
2> 104MΩ
3> 100MΩ
4> -- MΩ
Main:320MΩ
– Resistance –
5>
-- MΩ
6> -- MΩ
7> -- MΩ
8> -- MΩ
BACK
DATA LiPo–CELLS
BACK RES.
3.80 3.80 3.80 0.00 0.00 0.00
NiMH DONE
001:15S
Capacity : 53mAh
Current : 0.0A
Voltage : 8.16V
Resistance :
53mΩ
Peak Temp.
:
No sens
BACK
Graph
Cycle
Program select=LiPo
LiPo
CHG
DCHG
STOR
A
C
B
D
E
F
G
H
I
J
K
L M
N
O
LiPo STORAGE
Pack.Volt. : 11.1V/3S
Capacity : 2100mAh
Current : 2.1A
End Cell Volt :
3.80V
Press&Hold :
STORE
BACK
SELECT
LiPo STORE
000:11S
Capacity : 4mAh
Current : 2.0A
Voltage : 11.8V
Resistance :
375mΩ
Peak Temp.
:
No sens
STOP
Unit
Graph
LiPo DONE
000:11S
Capacity : 4mAh
Current : 2.0A
Voltage : 11.8V
Resistance :
375mΩ
Peak Temp.
:
No sens
STOP
Unit
Graph
Data LiPo = Graph
8.03V 000:34S
BACK
NiMH CHG
000:09S
Input Volt
:
12.24V
Delta Peak
:
1.8A
Int Temp
:
21ºC
Safety Timer :
240min
Capacity Limit :
2100mAh
STOP
Graph
NiMH DONE
000:09S
Input Volt
:
12.24V
Delta Peak
:
1.8A
Int Temp
:
21ºC
Safety Timer :
240min
Capacity Limit :
2100mAh
STOP
Graph
A.
Power Switch
b.
AC Power Input Port
C.
DC Power Input Port
D.
AC Power Cord
E.
Charger 1- LCD Screen
F.
Charger 2- LCD Screen
G.
Charger 1- Power Output Ports
h.
Charger 1- Balance Board Port
I.
Charger 1- Temperature Sensor Port
J.
Charger 1- Micro USB Port
(Software updates ONLY; do not use for charging)
K.
2.1A USB Power Output Port
L.
Charger 2- Micro USB Port
(Software updates ONLY; do not use for charging)
M.
Charger 2- Temperature Sensor Port
N.
Charger 2- Balance Board Port
O.
Charger 2- Power Output Ports
Not to scale.
Not all wiring shown.
Not all connectors shown.
CAUTION:
Only use 4.35V capable Li-Po batteries when using the Li-HV charge mode. Charging other Li-Po batteries in this mode can lead to property damage,
fire, or serious injury.
1. Press the
Left
and
Right Arrows
on the
LCD Touch screen
to scroll through
the main menu screens until you reach Program Select=Li-HV.
2. Press
ChG
.
3. The following
WARNING
screen appears. You must be sure you are using
High Voltage cells capable of being charged to 4.35 Volts.
4. Press
select
to continue to charging.
5. Follow Lithium (Li-Po/Li-Fe/Li-Ion/LI-HV) Charging, Dishcharging and Storage
insturctions
6. Press
back
to exit warning and choose another charging method.
Program select=LiHV
LiHV
CHG
DCHG
STOR
BACK
SELECT
WARNING!
Battery must be 4.35
V/Cell compatible. If
not property damage
fire or serious injury
could result.
