background image

CB-240

Operating instructions

CB-240

Operating instructions

Description of components

Punch US pitch for Legal, A4 or LTR Paper Format

Punch US pitch Extra Large Paper Format

How to punch

How to bind

Empty  the waste bin

Circulating punching lever : Removable and reassemble handle bar for both extra large and

normal format papers.

The machine is designed for binding using plastic binding combs of 6~51 mm. From the following table 

you can read off the appropriate binding comb size for the number of sheets you are binding.

Caution: the paper standard is 80g/m .

Dust cover : Keep the dust falling into the machine

Punching slot : For US pitch 21 ring plastic comb.

Blades : All blades may be disengaged by pulling them upward manually.

Paper edge guide : Left or middle or right 3 steps adjustable punching depth

     Figure-1 (select plastic comb size)

Hold your document tightly straight, 

Align 

Right

 end to get correct measurement

of document thickness and select proper 

plastic comb.

Plastic comb guide : Determining the binding comb size for your document.
Metal comb holding fingers : To hold the plastic comb for opening.
Metal hooks : Open plastic comb by hooking the finger rings.

7

Paper stopper-1 : Pushing frontward for punching normal format paper, pushing backward extra 

large paper.

8

Paper stopper-2 : By switching

 left 

or 

right

 for different format paper.

9

Plastic comb opening lever : Open plastic comb by pulling the lever.

10

Waste bin : Collects waste paper chips 

(WARNING! Be Sure to Clean Waste Bin Frequently. Overloaded Waste Chips Could Cause 

Punching Jam and Machine Damage.)

11
12

1.

2.

5.

8.

3.

4.

CB-240

Operating instructions

Instruction manual. . . . . . . . . . . . . . . . . .

    

 

Thanks for your purchase.Please carefully read through,

       

this introduction before use and keep it for future reference.

Metal pin : A guide pin for punching extra large paper.

13

Screws : For dividing the circulating punching lever.

14

Color Ginny

Comb Well

CB-120

CB-3000

CB-230

Binding comb dia.  6 8 10 12 14 16

20

22

25

28

32

38

44

50

Max. No. of sheets  25 45 65 95 125 145 175 210 240 270 310 375 440 500

         Figure-3 (page stopper-1)

1.Move Page stopper-1      backward for

   punching normal paper format.

2.Move Pape stopper-1      frontward for

   punching extra large paper. 

9

9

          Figure-4 (page stopper-2)

1.Punching the normal paper, you can move

   Page stopper-2      left or right for different

   paper format.

2.Make Page stopper-1 align paper format line.

10

         Figure-2 (select punching slot)

1.Paper edge guide      at three position.

2.

Right

 for plastic comb dia.

6~12mm

.

3.

Middle

 for plastic comb dia.

14~22mm

.

4.

Left

 for plastic comb dia.

14~51mm

.

5

General notes

You should initially carry out sample punching using waste paper. Remember that the maximum punching

capacity is 25 sheets. This specification refers to 80-g-paper (corresponds to the thickness of commercial 

copying paper). Punch transparent film and cardboard backs individually.

A scale is drawn on the front plate, with which you can determine the thickness of the document to be

bound(plastic comb guide). Therefore you can easily select the binding comb with the correct width.

Before punching and binding

1

   Move the page stopper-1      down.

2

   Align the sheets to 

A3 line

.

3

   Press down the single handle lever.

9

4

   To close the binding comb, push the 

     plastic comb opening lever 

     

downwards

.

5

   Remove the bound document.

7

2

   Pull the Plastic Comb Opening lever 

     far enough forward So that the binding

     Comb is opened widely.

3  

 Lay the paper over the comb fingers.

11

1

   Inserting the plastic binding comb in the  

     Metal Comb Holding Fingers 

 with 

     the side to be opened 

upward.

7

Punching depth adjustment

6.

7.

DSB Commercial Binding

System

3

   Lift up the circulating punching lever      . 

4

   Take out the sheets.

1

 Figure-6

1

   Put the sheets into punching slot      ,

     left-align 

to the page stopper-1     .  

2   

Press the circulating punching lever      down

     strongly with both hands to punch the sheets.

   

  (Note: max.25 sheet 80gsm paper or 2 sheets

     PVC cover)

4

1

9

  Figure-5 

4

   Reverse the punched sheets, insert the 

third

     right end 

punched hole to the extended metal  

     pin      (the 

Red area

 part), 

remain two holes

     at the right side of extended metal pin     .

5

   Press down the single handle lever.

3

3

2

1. Set the Paper Edge Guide      to the 

Right

 position (seen from the front) for documents with

    comb binding size 6mm to 12 mm. This setting corresponds to the standard setting.

2. Set the Paper Edge Guide      to the 

Middle

 position (seen from the front) for documents with

    comb binding size 14mm to 22 mm. The large punching depth prevents tearing of the bound

    document.

3. set the Paper Edge Guide      to the 

Left

 position (seen from the front) for documents with

    comb binding size 25mm to 51 mm. The large punching depth prevents tearing of the bound

    documents.

5

5

5

How to disengage the blades

Depending on the paper format, it is possible to 

Disengage any of the 24 blades. to do this, pull the

Unneeded blades upwards. the number of blades

needed For the format being used is given as

followed: Legal/14" with 

24

 punch holes;  A4 with

21

 punch holes; LTR with 

19

 punch holes.

This is how you punch and bind the sheets of yours document

1.  Select a sufficient size of plastic binding comb according to the paper amount (see plastic

     comb guide     ; Ref.figure-1).

2.  Place the plastic binding comb into the Metal Comb Holding Fingers      with the open side 

     upwards.

4. The rings are opened by the Metal Hooks      of the comb by pulling the binding back slowly

    forwards. Stop if the binding comb is opened far enough. The binding comb remains in the

    selected position.

5. Put the sheets you want to punch left aligned to the page stopper-1      and push them straight

    into the punching slot     . The page stopper-2      is manually adjustable to different formats.

    You can use the page stopper-1      for 24 ring punching or for 4-fold punching by moving the

    page stopper-1      frontward or backward.

6. Press the circulating punching lever      down strongly with both hands to punch the sheets of

    your document.

7. Place the punched sheets in the correct sequence into the opened binding comb.

8. Close the binding comb by pushing the plastic comb-opening lever      back. You can then

    remove the bound document.

This is how you punch sheets Extra Large Paper Format

1. Loosen 2 screws     on the side of the device.

2. Remove the longer part of the lever from the machine.

3. The punching lever can now only be operated with one hand.

4. Place the already punched page into the punching slot      in such a way that you can press

    one of the holes over the metal pin     at the lower end of the slot. This ensures that all holes

    have the same distance.

5. Now punch the remainder of the total punching width.

6. Screw the punching lever together again, when you have finished.(refer to "quick tip ......")

This is how you exchange pages of your bound document

1. Place the plastic binding comb (document with writing forwards) into the metal comb holding

    fingers     . Pull the plastic binding comb with the bound document between the metal comb

    holding fingers and lock it into the metal hooks     .

2. Press the binding comb carefully backwards until the plastic binding comb opens slightly.

3. You can remove or exchange sheets, when the spiral fingers have opened by approx.4-5 mm.

4. Then close the plastic binding comb by pushing the plastic comb-opening lever     .

6

4

4

8

10

11

11

13

14

7

8

7

9

9

9

1

12

3  

 Push the Waste Bin      back into the machine.

     Warning! Overloaded waste chip in the bin might cause punching jam and machine damage.

12

                                                          Figure-13 

1

   Remove the waste bin      completely.

12

2   

Empty the waste chips entirely.

Maintenance and care

1. You should regularly empty the waste bin     .

2. Films or cardboard should be punched separately.

3. Use the device only for punching paper, cardboard and protective sheets.

12

1

3

2

Figure-9

Figure-11

Figure-10

5

4

Left

Right

14

10

11

12

13

14

2

3

4

5

6

7

8

9

1

11

R

L

R

L

R

L

R

2

1

3

3

2

5

4

4

1

1

2

1

2

5

4

3

1

1

2

3

4

4

4

3

3

1

2

CB-240

Technical Data: 

Model No.

CB-240

Punching capacity

25 sheets (80gsm paper), 2 sheets PVC 0.20 mm

Binding comb size

6mm~51mm(500 sheets)

24 Selectable punch pins

Paper size 

Legal, A4, LTR and extra large up to 700mm width

Punching & Binding 

Two handles device accept same time operation

Loading of paper

Vertical

Paper guide line

Multiple(Legal,A4,LTR,A3)

Adjustable in three steps (2.5, 4, 5.5mm)

Edge guide

Punches

15Kg

Net weight

440

×

480

×

160(B

×

D

×

H)

Dimensions

Operating method

Manual

Left

Right

Backward

Frontward

Middle

Reviews:

Related manuals for CB-240