AeroLift 35
(220v)
Installation & Operating Instructions
Copyright © 2017 Draper Inc.
Form AeroLift35_220_Inst17-R
Printed in U.S.A.
If you encounter any difficulties installing or servicing your AeroLift 35, call your
dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999 or fax 765-987-7142.
Caution:
1
Read instructions completely before proceeding. Follow instructions carefully.
Installation contrary to instructions invalidates warranty.
2
Do not obstruct operation of AeroLift 35 with fingers or any other
object. Serious injury or damage could result.
3
It is not uncommon to overheat the motor during initial installation when
setting limits. The motor is thermally protected and will stop working
temporarily. DO NOT physically pull the unit down when this occurs. Once it
has cooled to a safe temperature, it will begin operating again.
4
The AeroLift 35 is designed to accommodate ceiling suspended
equipment. Equipment should not be allowed to rest on ceiling closures
during operation (see “Installing Projector”).
5
Entire bottom of unit must be unobstructed to permit proper operation.
6
Unit must be installed level (use a carpenter’s level).
7
Unit operates on 220-230V AC current.
Note:
Unit has been thoroughly inspected and tested at factory and found to be
operating properly prior to shipment.
Planning
1
Based on screen location and projector specifications, determine proper
position for projector installation.
2
Confirm that there is adequate space for installation and operation. Minimum
clearance above ceiling level varies according to height of projector, projector
mounting bracket, optional ceiling closure and optional Environmental Air
Space Housing.
3
Arrange to provide service access to the unit.
4
Total maximum capacity for the AeroLift 35 is 15.9 kg.
(including closure, projector and bracket).
As Soon As AeroLift Arrives
1
Open carton and inspect for damage.
2
Locate the following parts:
A. The unit itself
B. Controls
C. Any optional equipment
3
Test lift
prior to installation
.
AeroLift 35
(with Closure panel)
Hanging Unit
The AeroLift is provided with four (4) mounting angles for suspending or direct mounting the unit from above, or direct mounting from the sides. These angles provide
up to 32mm of adjustment (side to side). The AeroLift 35 is designed to fit between joists spaced 41cm apart on center (assuming 51mm joists), and to close to
aproximately 102 mm, not including the projector, bracket or closure. The unit should be guy wired or blocked to prevent swinging.
All installations should observe the following guidelines:
1
Installer must ensure that all fasteners and supports are of adequate strength to securely support AeroLift 35 and projector. It is recommended that hardware
structure be able to hold at least four times the combined weight of the lift, projector, housing, closure and ceiling material attached to closure.
Caution: DO NOT hang from, "ride" or pull down on the unit.This could create a failure and cause damage and/or injury.
2
Fastening methods must be suitable for mounting surface, and securely anchored
so vibration or abusive pulling on unit will not weaken installation.
3
Bottom of unit must be unobstructed after installation.
Sufficient clearance must be allowed below projector or optional ceiling closure.
4
Do not use unit to support adjacent ceiling, light fixtures, etc.
5
Do not complete the ceiling below the unit until electrical
connections
have been completed and unit has been operated successfully.
6
Use slots on the projector plate and on the closure to adjust the
unit to ensure proper alignment of ceiling closure relative to
ceiling opening.
508mm
257mm
492mm
479mm
1
1
/
4
"
19mm
565mm
122mm
318mm
Top View
Side View
318mm
318mm
Front View
AeroLift 35
(Relevant Mounting Dimensions)
Top
Mounting
Hole
Side
Mounting
Slots
Top
Mounting
Hole
Anti-Slip
Hole
Side
Mounting
Slots
Figure
(1)
Projector can be installed as shown or
turned 90° depending on projector size.
220V
Receptacle
