background image

http://www.tulsawinch.com

SEL-0061-001

                     

REV 0 

July 2020

 

TABLE OF CONTENTS 

SAFETY NOTES .......................................................................................................................... 2

 

INTRODUCTION AND THEORY OF OPERATION ........................................................................ 3

 

HYDRAULIC SCHEMATIC........................................................................................................... 4

 

MAINTENANCE AND SERVICE ................................................................................................... 5

 

WIRE ROPE ............................................................................................................................... 7

 

DISASSEMBLY ........................................................................................................................... 8

 

ASSEMBLY ................................................................................................................................. 9

 

SERVICING THE MOTOR ......................................................................................................... 10

 

SERVICING THE BRAKE........................................................................................................... 11

 

SERVICING THE PLANETARY SETS ......................................................................................... 13

 

TROUBLESHOOTING ............................................................................................................... 14

 

TORQUE SPECIFICATIONS CHART.......................................................................................... 15

 

BILL OF MATERIAL.................................................................................................................. 16

 

EXPLODED ISOMETRIC ASSEMBLY DRAWING ....................................................................... 19

 

Summary of Contents for TWG TULSA WINCH 1200W




















Reviews: