![background image](http://html.mh-extra.com/html/dmp-electronics/692f/692f_installation-sheet_2514012001.webp)
InstallatIon sheet
692F Fire Command LED Keypad
Description
The 692F Fire Command LED Keypad offers 5 sets of highly visible LED annunciation of alarm and trouble conditions
on DMP XR5FC and XR5SL Commercial Fire/Communicator Panels. The 692F provides individual zone alarm and
trouble LEDs for zones one to five. Also, system LEDs, an internal sounder, 2-button Fire alarm initiation, and
Silence, Reset, and Fire Drill functions are provided. The 692F operates on 8.0 to 16 VDC at 30mA in normal mode
and can draw up to 70mA in alarm.
Removing the Keypad Base
The 692F is made up two parts: the front, containing the circuit board and other components, and the base. To
remove the base, insert a flat screwdriver into one of the openings on the bottom and carefully twist it while gently
lifting the keypad from the base. Repeat with the other opening, then lift the keypad from the base.
Inserting the Reference Card
A reference card has been supplied with the 692F
keypad. The reference card is provided to assist the users
when operating their security systems. Write the zone
descriptions on the front of the card. Slide the card in the
back of the base before installing the keypad. Refer to
Figure 1 for reference card installation.
Installing the Keypad
The 692F has been designed to easily install on any
4-square box, 3-gang switch box, 695 and 696 backbox,
or on any flat surface. Figure 1 shows the mounting hole
locations on the keypad base.
Wiring the Keypad
The 692F keypad is supplied with a single 4-wire harness
for connection to the XR5FC to XR5SL panel’s keypad data
bus wiring. Connect the 4-wire harness to the back of the
PCB as shown. Then connect the wires to the panel terminals 7, 8, 9, and 10.
Buzzer Operation
Each time a user presses a key on the 692F, the buzzer emits a short tone. After the user performs a successful
keypad operation, the buzzer emits a 1/2 second tone. If the operation is not successful, the buzzer emits four short
tones. This alerts the user to perform the function again. During trouble conditions, the keypad emits a steady tone
to alert the user. Entering the user code silences the buzzer.
Keyboard Backlighting
The keyboard on the 692F lights anytime a key is pressed or the alert buzzer sounds making it easy for users in
darkened rooms to enter their code or perform a command.
984 COMMAND
Enter 984 + COMMAND to allow the panel to pick up the phone line when a Remote Link™ computer is calling
the panel. If the panel was previously programmed to answer calls from Remote Link™, the panel will answer
automatically.
Enter 984 + COMMAND plus up to a 15-digit phone number to contact a Remote Link™ computer from the panel.
Zone Alarm and Trouble LEDs
The 692F contains five red zone alarm LEDs and five yellow zone trouble LEDs. The red alarm LEDs turn on
steady during an alarm condition and turn off when the zone has restored to normal and a Sensor Reset has been
performed. If the zone alarm or trouble is a Supervisory type zone, the LED pulses (1 second on, 1 second off).
The yellow trouble LEDs turn on during a trouble condition, turn off when the zone restores to normal, and wink
(1/4 second on, 1 3/4 second off) when the zone has been bypassed.
Three System LEDs
The 692F has three system LEDs. The system LEDs are located near the top left corner of the keypad.
Yellow Silenced LED
turns on when the bells are silenced manually from the keypad or after the
Bell Cutoff time. The Silenced LED turns off if the alarm sounds again or when a Sensor Reset
is performed.
Surface and Backbox
Mounting Holes
Surface and Backbox
Mounting Holes
Guide Tabs
Reference Card
Surface and Backbox
Mounting Holes
Surface and Backbox
Mounting Holes
Surface and Backbox Mounting Holes
Combined 4-Square
and 3-Gang Switch Box
Mounting Holes
Black - 10
(Ground)
Green - 9
(Panel to Keypad Data)
Yellow - 8
(Keypad to Panel Data)
Red - 7
(Auxiliary Power)
Figure 1: 692F Wiring and Mounting Diagram