Parts and Description
The MEGApix Camera is designed to be surface mounted on a wall
or ceiling.
RJ-45 Cable
Bracket
Pan/Tilt Stopper Screw
DC Power Cable
Lens
SD Card Slot
Reset Button
67.5 (2.65”)
63.8 (2.51”)
161.7 (6.36”)
76.0 (3.0”)
146.7 (5.77”)
Pressing the reset button on the camera’s control board for five (5) seconds will
initialize all environmental variables to factory default. Previous setup for IP default,
time, etcetera will be deleted. If a system IP address is lost, reset the camera back
to factory default.The following are the default network settings:
IP Mode
DHCP
IP Address
192.168.1.123
Subnet Mask
255.255.255.0
Gateway
192.168.1.123
Command Port
7000
HTTP Port
80
Live Port
7001
Resetting the Camera
DWC-MB721M4TIR
DWC-MB721M8TIR
IP 2.1MP Weather Resistant Bullet IR Camera
Mounting the Camera
1. Use the camera’s mounting template or the camera’s housing to mark the
drilling holes in the mountng surface.
2. Drill holes into the drywall using the included dry wall anchors.
3. Pull wires through and make connections. Refer to “
Network Connection
”
for more information.
Mount the camera to the wall or ceiling using
the screws provided with the camera.
4. To adjust the camera’s pan and tilt,
loosen the Pan/ Tilt stopper screw a little
before mounting the camera.
5. Once the camera’s pan and tilt angles
have been adjusted, tighten the Pan/
Tilt stopper screw back to secure the
camera in its position.
Prepare the Camera and Mounting Surface
INSTALLATION
!
Frequent use may cause a System Error
Recommended Settings
Camera Default Color Settings
5
7
8
Additional Cabling Connections
NETWORK
ENVIRONMENTAL
Frame Rate
Up to 30fps at All Resolutions
Video Compression Type
H.264, MPEG4, MJPEG (Super Fine~Low)
IP
IPv4, IPv6
Protocol
TCP/IP, HTTP, DHCP, PPPoE, ICMP, ARP, RARP,
RTSP, NTP, UDP, Multicast
LAN
802.3 Compliance 10/100 LAN
Web Viewer
OS: Windows XP / Vista / 7, MAC OS
Browser: Internet Explorer, Chrome, Firefox, Safari
Video Management Software
NxMS, DW Spectrum, Pivot
ONVIF Conformance
Yes
Streaming Capability
Dual-Stream at Different Rates and Resolutions
Power Requirement
DC 12V, PoE (IEEE802.3af Class 2)
Power Consumption
3.5W, 300mA / LED ON: 5W, 430mA
Operating Humidity
Less than 90% (Non-Condensing)
Operating Temperature/ Humidity
-10
o
C ~ 50
o
C (14
o
F ~ 122
o
F)
Other Certifications
CE, FCC, RoHS
Memory Slot
24 hours recording to Micro SDHC Card (4GB-32GB)
Card Not Included*
Dimensions
161.7 x 67.5 mm (6.36 X 2.66 in)
Material
Aluminum Housing
Weight
0.93 lbs
Maximum User Access
5 Users
MECHANICAL
ELECTRICAL
Resolution
1920X1080 (16:9) ~ 320X240 (4:3)
IP Rating
IP66 (Protects against dust and high pressure water)
LENS
IMAGE
Image Sensor
1/2.8” Sony CMOS Sensor
Effective Pixels
1920 (H) X 1080 (V)
Minimum Scene Illumination F2.0 (30IRE): 2.4 Lux [Color], F2.0 (30IRE): 0.5 Lux [B/W]
Zoom
12x Digitzl Zoom
Lens Type
Fixed Lens
Focal Length
4.0mm [DWC-MB721M4TIR]/ 8.0mm [DWC-MB721M8TIR]
Angle of View
Horizontal: 42
o
Wide Angle
IR Distance
50ft Range IR
Quick Setup Guide
Template Sheet
Before mounting the camera, please check the following:
1. The mounting surface must be able to sustain five times the weight of your
camera.
2. Do not let the cables get caught in improper locations or it can cause
damage to the cables.
Thank you for purchasing Digital Watchdog’s MEGApix Weather Resistant Bullet Camera.
Before installing the camera, please verify your model and read this guide carefully.
20140122
The following items are included with a MEGApix Bullet camera
L-Wrench
IR Bullet Camera
- 12VDC Power
- RJ45 Network
Please refer to the table below for the default camera settings.
You can reset the camera’s settings to its default color settings by
pressing the ‘Default’ button at the bottom of the screen.
Network Connection
There are two options.*
Using a Non-PoE Switch
Using a PoE-Enabled Switch
The MEGApix Camera is PoE-compliant, allowing transmission of power
and data via a single ethernet cable. Follow the illustrations below to
connect the camera to a PoE-enabled switch using an ethernet cable.
If a PoE-enabled switch is not used, use a power adaptor to connect the
MEGApix Camera to a Non-PoE switch.
1
2
PREPARATION
TEL: (866) 446-3595
www.Digital-Watchdog.com / [email protected]
Technical Support Hours: Monday-Friday 9:00AM to 8:00PM EST
INSTALLATION
Quick Start
Guide
Mounting
Template
CD
(Manual &
Software)
2
3
4
6
Camera Specifications
4 Screws & 4
Dry Wall
Anchors
DWC-MB721M4TIR
DWC-MB721M8TIR
IP 2.1MP Weather Resistant Bullet IR Camera
Quick Setup Guide
