Dell Precision M20 Скачать руководство пользователя

Страница: 1 / 47

Dell Precision™ M20 Service Manual

Notes, Notices, and Cautions

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text:

Dell

, the

DELL

logo, and

Dell Precision

are trademarks of Dell

Inc.;

Intel

is a registered trademark of Intel Corporation;

Bluetooth

is a registered

trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc. under license.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.

Model PP11L

January 2005 Rev. A00

Before You Begin

System Components

Hard Drive

Memory Module, Modem, and Devices

Coin-Cell Battery

Mini PCI Card

Internal Card With Bluetooth

Wireless Technology

Center Control Cover

Keyboard

Display Assembly and Display Latch

Palm Rest

Fan

Microprocessor Thermal-Cooling Assembly

Microprocessor Module

Speaker Assembly

Base Latch

System Board

Pin Assignments for I/O Connectors

Flashing the BIOS

NOTE:

A NOTE indicates important information that helps you make better use of your computer.

NOTICE:

A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION:

A CAUTION indicates a potential for property damage, personal injury, or death.

Содержание Precision M20
















































Результаты поиска

Содержание Precision M20

Отзывы:

Похожие инструкции для Precision M20

Бренды по названию

Популярные бренды

Dell Precision M20, Руководство по обслуживанию

Результаты поиска

Содержание Precision M20

Отзывы:

Похожие инструкции для Precision M20

Бренды по названию

Популярные бренды