background image

 

 
 
 
 
 

Dell™ PowerConnect™ 3424/3448/3424P/3448P 

 

PowerConnect 3424/3448/3424P/3448P 
Release Notes 

 

 

 
 

Date: November 2006 
System Firmware Version 2.0.0.20 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Information in this document is subject to change without notice. 

© 2006 Dell Inc. All rights reserved. 

Reproduction in any manner whatsoever without the written permission of Dell Inc

 

is strictly forbidden. 

Trademarks used in this text: Dell, the DELL logo and PowerConnect are trademarks of Dell Computer Corporation; Microsoft 

and Windows are registered trademarks of Microsoft Corporation. 

Other trademarks and trade names may be used in this document to refer to either the entity claiming the marks and names or 
their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own. 
All rights reserved. This document may not, in whole or in part, be copied, photocopied, reproduced, translated, or reduced to any 
electronic medium or machine readable form without the prior written consent of Dell. Dell reserves the right to make changes 
without further notices to any products or specifications referred to herein to improve reliability, functionality or design.  
Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under the copyright 
laws. 

Summary of Contents for PowerConnect 3424










Reviews: