background image

Dell™ Studio 1735/1737 Service Manual 

 

 

Notes, Notices, and Cautions 

Information in this document is subject to change without notice. 

© 2008 Dell Inc. All rights reserved.

 

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. 

Trademarks used in this text: 

Dell

 and the 

DELL

 logo are trademarks of Dell Inc.;

Bluetooth

 is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell under 

license. 

Microsoft

Windows, and Windows Vista 

are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. 

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any 
proprietary interest in trademarks and trade names other than its own. 

Model PP31L 

October 2008             Rev. A01

 

Before You Begin

 

Base Cover

 

Hard Drive

 

Memory

 

Coin-Cell Battery

 

Processor Heat Sink

 

Processor

 

Center Control Cover

 

Keyboard

 

Display

 

Camera (optional)

 

Palm Rest

 

Optical Drive

 

Speakers

 

System Board

 

Fan

 

Charger Board

 

Communication Cards

 

Audio Board

 

Microphone

 

Battery Latch Assembly

 

Flashing the BIOS

 

NOTE: 

A NOTE indicates important information that helps you make better use of your computer. 

NOTICE: 

A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. 

 

CAUTION: 

A CAUTION indicates a potential for property damage, personal injury, or death. 

Summary of Contents for 1737 - Studio - Laptop
















































Reviews: