Dataprobe iBootBar iBP-N15 Installation And Operations Download

Page: 1 / 21

Technical Support Hotline: (201) 934-5111 [email protected]

Main: 201-934-9944 Website: dataprobe.com

Scope of this Document:

This document covers the installation and operations of Dataprobe’s iBootBar series of remote power control
units. The following models are covered in this document:

Model

Power Feed / Total Capacity

Outlets

Control

iBP-N15

NEMA 15 Amp

8 x NEMA 5-15

IP Control, Serial Control

iBP-N15-M

NEMA 15 Amp

8 x NEMA 5-15

IP Control, Serial Control, Internal Modem

iBP-2N15

2 x NEMA 30 Amp

8 x NEMA 5-15

IP Control, Serial Control

iBP-2N15-M

2 x NEMA 30 Amp

8 x NEMA 5-15

IP Control, Serial Control, Internal Modem

iBP-N20

NEMA 20 Amp

8 x NEMA 5-15

IP Control, Serial Control

iBP-N20-M

NEMA 20 Amp

8 x NEMA 5-15

IP Control, Serial Control, Internal Modem

iBP-2N20

2 x NEMA 40 Amp

8 x NEMA 5-15

IP Control, Serial Control

iBP-2N20-M

2 x NEMA 40 Amp

8 x NEMA 5-15

IP Control, Serial Control, Internal Modem

iBP-C10

IEC C14 10 Amp

8 x IEC C13

IP Control, Serial Control

iBP-C10-M

IEC C14 10 Amp

8 x IEC C13

IP Control, Serial Control, Internal Modem

iBP-2C10

2 x IEC C14 20 Amp

8 x IEC C13

IP Control, Serial Control

iBP-2C10-M

2 x IEC C14 20 Amp

8 x IEC C13

IP Control, Serial Control, Internal Modem

iBP-C20

IEC C20 20 Amp

8 x IEC C13

IP Control, Serial Control

iBP-C20-M

IEC C20 20 Amp

8 x IEC C13

IP Control, Serial Control, Internal Modem

iBP-2C20

2 x IEC C20 40 Amp

8 x IEC C13

IP Control, Serial Control

iBP-2C20-M

2 x IEC C20 40 Amp

8 x IEC C13

IP Control, Serial Control, Internal Modem

iBootBar

Precision Version 1.41.32

Installation and Operations

Ref: iBootBar_Precision_v20160428e.doc

Summary of Contents for iBootBar iBP-N15






















Search results

Summary of Contents for iBootBar iBP-N15

Reviews:

Related manuals for iBootBar iBP-N15

Brands by name

Popular brands

Dataprobe iBootBar iBP-N15, Installation And Operations

Search results

Summary of Contents for iBootBar iBP-N15

Reviews:

Related manuals for iBootBar iBP-N15

Brands by name

Popular brands