Cross Technologies 2099-1318 Instruction Manual Download

Page: 1 / 21

Instruction Manual

Model 2099-1318

10MHz Source/Inserter, Redundant Power

August 2017, Rev. A

ALARM

LNB1

DC ON

REF ON

LNB2

MENU

EXECUTE

ALARM

PSA
PSB

EXT REF

REMOTE
OVEN

MODEL 2099

SOURCE / INSERTER

LNB1 +13.2V @ 0.249A

LNB2 +18.1V @ 0.251A

ROSS

ECHNOLOGIES

INC

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment. Printed in USA.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.

ROSS

ECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB: www.crosstechnologies.com

E-MAIL: [email protected]

Summary of Contents for 2099-1318






















Search results

Summary of Contents for 2099-1318

Reviews:

Related manuals for 2099-1318

Brands by name

Popular brands

Cross Technologies 2099-1318, Instruction Manual

Search results

Summary of Contents for 2099-1318

Reviews:

Related manuals for 2099-1318

Brands by name

Popular brands