CLW-DIM, DIMS, & SLVD(W/A/B)
Introduction
Specifications
Following are specifications for the -DIM, -DIMS, and
-SLVD.
Features and Functions
The CLW-DIM (-DIM) is a stand-alone wall box dimmer
that can also act as a Cresnet
®
device that reports to a
Crestron
®
control processor. The CLW-DIM has four
preset lighting levels that can be adjusted (refer to note
below). The CLW-DIM also includes two isolated, non-
polarized Cresnet wires (plus a ground wire) for
connecting to the Cresnet network over a twisted pair
wire with shield.
CLW-DIM, CLW-DIMS, & CLS-SLVD Specifications
SPECIFICATION DETAILS
Power Requirements
Line Power, 120 VAC, 60 Hz
Default Net ID
-DIM: 6D
-DIMS: 6E
Switch Type
Dimmer
Load Type
Incandescent, Tungsten-Halogen,
Magnetic Low Voltage
2-Series Control System
Update File
1,2
Version 3.093 or later
Load Ratings
3
Incandescent/Tungsten
Halogen
-DIM: 1000W
-DIMS: 1000W
-SLVD: N/A
Magnetic Low Voltage
4
-DIM: 1000VA/750W
-DIMS: 1000VA/750W
-SLVD: N/A
Operating Temperature
and Humidity
32°F to 104°F (0°C to 40°C)
10 to 90% Relative Humidity
(Non-Condensing)
Dimensions and Weight
-DIM and -DIMS:
Height: 4.13 in (10.48 cm)
Width: 2.38 in (6.03 cm)
Depth: 1.91 in (4.85 cm)
Weight: 4.9 oz (0.67 kg)
-SLVD:
Height: 4.13 in (10.48 cm)
Width: 1.75 in (4.45 cm)
Depth: 1.91 in (4.85 cm)
Weight: 3.6 oz (0.50 kg)
NOTE:
The four preset levels are noted as Button 1-
High, Button 1-Low, Button Preset 2, and Button Preset
3. Preset “Button 1-High” is usually used for turning
lights on to full brightness while preset “Button 1-Low” is
usually used for turning the lights off. Although “1-High”
and “1-Low” are usually used for “On” and “Off”
respectively, the light level for each preset can be
customized by the user. Refer to “Operating Buttons and
Switches” on page 5 for more information on customizing
light levels.
The CLW-DIM features a three-position mode selection
switch. Refer to “Operating Buttons and Switches” on
page 5 for more information. In the absence of Cresnet
communications, the dimmer can still be used to control
lighting.
The CLW-DIMS (-DIMS) is similar to the -DIM with the
added capability of working with a slave unit
(CLW-SLVD) in a multi-switch / single circuit
application.
The CLW-SLVD (-SLVD) is a slave unit that when used
in conjunction with the -DIMS acts as an additional
dimmer control point in a multi-dimmer / single circuit
application. It does not connect to a Cresnet system and
cannot be used without a -DIMS. The -SLVD does not
have a mode selection switch and is not programmable. It
emulates the operation of the -DIMS to which it is
connected.
1.
The latest software versions can be obtained from the Crestron
website. Refer to the NOTE following these footnotes.
2.
Crestron 2-Series control systems include the AV2 and PRO2.
Consult the latest Crestron Product Catalog for a complete list of
2-Series control systems.
3.
Refer to Derating Charts for Multigang Installations on page 3.
The -DIM, -DIMS, and -SLVD are available in white,
almond, and black. White units are designated by part
numbers ending in “W”. Almond units are designated by
part numbers ending in “A”. Black units are designated by
part numbers ending in “B”. Each dimmer can be covered
with a decorative faceplate (not supplied).
4.
VA ratings are for input power to the transformer. If you do not
know the input power requirement of the transformer, use the
bulb’s wattage rating to determine proper rating.
NOTE:
Crestron software and any files on the website
are for Authorized Crestron dealers and Crestron
Authorized Independent Programmers (CAIP) only. New
users may be required to register to obtain access to
certain areas of the site (including the FTP site).
Crestron Electronics, Inc.
Installation Guide – DOC. 5995B
15 Volvo Drive Rockleigh, NJ 07647
(2002077)
Tel: 888.CRESTRON
06.05
Fax: 201.767.7576
Specifications subject to
www.crestron.com
change without notice.
