background image

         

WARNING:

 If the information in these instruc-

tions is not followed exactly, a fire or explosion may 

result causing property damage, personal injury or 

loss of life.

 

- Do not store or use gasoline or other flammable  

       

   vapors  and liquids in the vicinity of this or any  

   other appliance. 

WHAT TO DO IF YOU SMELL GAS:

 Do not try to light any appliance.

 Do not touch any electrical switch; do not use  

  any phone or cell phone in your building.

 Immediately call your gas supplier from a neighbor’s 

  phone. Follow the gas supplier’s instructions.

 If you cannot reach the gas supplier, call the fire 

   department.

 Installation and service must be performed by a    

   qualified installer, service agency or the gas supplier.

90N

GAS FIRED VENTED  

FLOOR FURNACE 

        WARNING:

 This product can expose you to 

chemicals including epichlorohydrin which is known 

to the State of California to cause cancer and birth  

defects and/or other reproductive harm. For informa-

tion go to www.p65warnings.ca.gov

MODEL NUMBERS 

(natural gas)

90N30A / 90N50A / 90N65A

MILLIVOLT CONTROL SYSTEM

250 West Laurel Street, Colton CA 92324  •  www.cozyheaters  •  1-888-444-1212  

        WARNING:

 Installation and repair must be done 

by a qualified service person. The appliance should 

be inspected before use and at least annually by a 

professional service person.

INSTALLER: 

Leave this manual with the appliance. 

CONSUMER: 

Retain this manual for future reference.

-  The coating selected to provide longer life to the  

 

  heat exchanger 

may smoke slightly upon initial firing.  

  Please provide adequate ventilation if this occurs.

-  Installation, maintenance, service, troubleshooting     

  & repairs must be performed by a qualified service    

  agency. DO NOT attempt any of these procedures  

 

  if you are not qualified as this could expose you to  

 

  property damage, personal injury, or loss of life and  

  will invalidate all warranties.

-  This unit is for residential use only and is not approved  

  for installation in mobile homes, greenhouses, or  

 

  environments involving dusty, wet, corrosive, or  

  explosive conditions. Such conditions will invalidate  

  the warranty and may create unsafe conditions. 

         WARNING: Operation of this furnace when not 

connected to a properly installed and maintained 

venting system can result in Carbon Monoxide (C.O.) 

poisoning and possible death. For your safety, this 

furnace and the venting system should be inspected 

at least annually by a qualified service technician.

OWNER’S MANUAL

INSTALLATION INSTRUCTIONS

VISITE NUESTRA PÁGINA WEB PARA LA VERSIÓN EN 

ESPAÑOL DE ESTE MANUAL 

 

https://www.cozyheaters.com/products

Summary of Contents for 90N30A and













































Reviews: