ConforTeck™ DUO™
Attention: New firmware with modifications for error messages
Description
(1)
“DOWN” buttons (blue) to set down the power level.
(2)
“UP” buttons (red) to increase power level.
(3)
Digital display. Show the selected power level (display shut off after 10 seconds of
last setting) or error messages. The dot indicate if power supply is right.
(4)
Output lighted indicators light up only when equipment works normally.
(5)
Back lighted buttons locators to help use the control buttons at night.
(6)
Controlled outputs of your DUO™. DC 2.5x5.5mm power jack. Will drive any resistive
heating equipment up to 55 Watts at 13.8 Volts DC.
(7)
ConforTeck™ neck strap to wear your DUO™ at neck (not showed).
(8)
DC 2.5x5.5mm plug powering your DUO™. Plug it into any DC jack at 12 Volts DC to
use your DUO™.
Warning
:
Risk of burns if this product is not used as indicated by manufacturer. On a
regular basis, check the part of the body that is exposed to heat to avoid getting burn
without realizing it. Anyone with blood pressure problems, suffering from diabetes or
paralysis must ask a physician before using this equipment. Anyone experiencing
difficulties perceiving heat on skin or unable to express themselves properly SHOULD
NEVER uses this product. If in doubt, consult your physician.
User manual
CONFORTECK™ IS TO BE USED EXCLUSIVELY IN THE OUTDOORS UNDER WINTER CONDITIONS.
1.
Please read these instructions carefully before starting operation.
2.
No installation needed. Simply use your ConforTeck™ equipments as describe in user manual. Now plug these into the respective output of your DUO™.
The wires are to be worn inside the snowsuit and the DUO™ is to be worn inside or outside as you wish. Connect the DC power plug (7) of your DUO™ into a
DC 2.5x5.5mm jack at 12 Volts DC or in a ConforTeck™ Énergie™(CTKE12V), a “C” type batteries pack (B8C) or any 12 Volts DC power source. You can also
plug it in an accessory jack (cigar lighter) using the needed adapter (adapter not included). The dot in the lower right corner of the display will goes steady
red when controller is correctly powered. Flashing dot mean power is under 10 volts.
3.
To use your DUO™, just press the up or down buttons to set the needed power between “0” and “F” (F for full = 10) for each output. Use the higher levels to
rapidly rise up the temperature and after, set it to a lower level to get comfortable. At level zero, your DUO™ will not generate any heat. To set it off, simply
unplug the DUO™.
4.
When you will plug it back online, your DUO™ will restart a last selected level.
5.
Your DUO™ will tell you if a problem is detected. If your DUO™ show an “O”, the equipment plugged to one of the output of the DUO™ need to much
power (more than 95 Watts at 13.8 Volts DC) or a short-circuit have been detected away from the DUO™, on this same output (the pictogram will blink). In
this case, the output is deactivated and you need to press a button to reactivate the output. If equipment plugged in an output works normally, the
indicator of this output will be steady red. If the indicator is intermittent, the equipment works intermittently too and if the indicator is off, the equipment is not
working at all.
Device care
Occasionally verify that connections are clean a free from ice, humidity and oxidation.
Antioxidant grease must be applied on the jacks.
Do not use any aggressive product to clean the DUO™. Simply use a humid towel.
Technical specifications
Electrical
Operating voltage : 8 to 16 Volts DC.
Short-circuit protection : Detection and deactivation of the output.
Auto save : Your ConforTeck™ is provided with a memory system which records the last selected levels 10 seconds after last setting.
Each output can control up to 55 Watts of power at 13.8 Volts DC (4 amp).
Mechanical
Height
0.984” (25mm)
Width
2.047” (52mm)
Length
4.331” (110mm)
Weight
0.2 lb (128g)
Environmental
Operating temperature : -40°C to +70°C
Relative humidity : 0 to 95% without condensation
Design, specifications and/or price are subject to change without notice. ©2013
