Tools Required and Parts List
DESCRIPTION
CHD PANEL
RACK SCREW
QUANTITY
1
4
PARTS LIST
Compact High Density (CHD) Panel
#2 PHILLIPS
SCREWDRIVER
Remove the CHD Panel from the Packaging
NOTE:
The mounting/shipping brackets (one on each side of the panel) are
located behind the mounting brackets in the place shown. After being
removed from the panel, they can be discarded unless used
for 23 in. rack mounting.
For 19-in. Rack Mounting:
Remove the Two 23-in. Mounting/Shipping Brackets
2
Select (a) Mounting Position, (b) Grounding Method,
and (c) Whether to Use Optional Side Plates.
(a) The panel mounts on front or rear of a 3-inch or
6-inch channel. The channel can be a frame or the
internal front supports of a cabinet. Mount as shown.
(b) Ground per local practice in the location
shown. Two-hole grounding requires
a 0.625-inch spacing
between mounting holes
(ground lug not
included).
3
4
3.0 IN.
(76.2 CM)
6.0 IN.
(152.5 CM)
RIGHT SIDE VIEW
OF PANEL
FRONT OBLIQUE VIEW
OF PANEL
MOUNTING POSITION FOR FRONT OF 3-INCH CHANNEL
MOUNTING POSITION FOR BACK OF 3-INCH CHANNEL
MOUNTING POSITION FOR BACK OF 6-INCH CHANNEL
MOUNTING POSITION
FOR FRONT OF
3-INCH CHANNEL
MOUNTING POSITION FOR BACK
OF 3-INCH CHANNEL
MOUNTING
POSITION
FOR BACK
OF 6-INCH
CHANNEL
GROUNDING
LOCATION
(OPTIONAL)
26886-A
with accessories and this quick start manual.
Mount Panel in Channel
Rack or Cabinet
NOTE:
This document shows the panel being installed on a 19-inch rack.
FRONT OBLIQUE VIEW
LEFT SIDE OBLIQUE VIEW
CABINET
MOUNTING
CHANNEL RACK
MOUNTING
SIDE PLATE, LARGE CABLE
2
This document shows the 2RU model in most illustrations.
The CHD Panel is also offered in a 1RU and 4RU models. Procedural
and physical details are analagous for the 1RU and 4RU models.
NOTE:
There will be cardboard and/or plastic inserts inside of the
panel to prevent damage during shipment.
Front door and rear cover will need to be opened to
remove them.
1
24.0 IN.
(242.5 CM)
CHD
PRODUCT PAGE
QR CODE;
ACCESS WITH
SMARTPHONE
FOR CHD
USER MANUAL
AND FIBER
CONNECTOR
CLEANING
INSTRUCTIONS
Use M6 or #12-24 screws
(provided) as appropriate.
CHANNEL RACK MOUNTING:
Cable Mounting Bracket
(EHD-RMB) mounts to rear rail and
provides point to secure trunks.
Vertical Cable Mounting Bracket
(EHD-RMB-GAB) mounts to rear rail
and allows cable attachment
molding to snap into bracket for
top down or bottom up securing of
CommScope trunks with gland
adapters.
UMB Bracket (UMB-RMB-LG) can
be installed above or below panel
(usually not used on same rack as
EHD brackets).
CABINET MOUNTING:
is done using same accessories
(with different catalog numbers)
modified for use in cabinet.
NOTE: Front and back rails should
be 24 inches (60.96 cm) apart
when mounting with 3-inch
(7.62 cm) recess.
Cable Mounting Bracket
(EHD-CMB)
Vertical Cable Mounting Bracket
(EHD-CMB-GAB)
UMB Bracket (UMB-CMB-LG)
Usually not used in same cabinet
with EHD brackets.
(c) Default side plates can be removed
by sliding them out. Slide in optional
side plates for larger sized cables.
EHD-CMB
EHD-RMB
EHD-RMB-GAB
EHD-CMB-GAB
UMB-RMB-LG
UMB--CMB-LG
CABLE BRACKETS ARE ACCESSORIES; MUST BE
ORDERED SEPARATELY.
Quick Start
CommScope (logo), CommScope, and CHD are trademarks.
860649630 Rev A
© 2019, CommScope, Inc. All Rights Reserved.
TC-96269-IP · Rev A · June 2019
