CNC QB2 User Manual Download

Page: 1 / 21

Page 1

QB2 CNC

User guide

Safety precautions

Like any power tool, operating and using a CNC machine can be dangerous. Diligence must be applied when operating

any machine. It is recommended to wear appropriate PPE such as eye protection and ear muffs for your own safety.

NEVER leave a powered machine unattended at any time!

In the event of an issue or if something doesn’t seem right, it is recommended to immediately disconnect power to

the machine and unplug it from the wall power outlet. Contact our customer support team if you have any concerns

about your machine.

Always ensure your machine is free and clear of any swarf, dust or other obstructions that may impact the motion of

your machine. We highly recommend the use of a Dust shoe and vacuum system for keeping your machine clean and

clear of swarf and dust.

Always ensure to follow the maintenance guide at the bottom of this manual after initial assembly and setup and also

periodically to ensure your machine always performs to its optimal capacity.

Summary of Contents for QB2






















Search results

Summary of Contents for QB2

Reviews:

Related manuals for QB2

Brands by name

Popular brands

CNC QB2, User Manual

Search results

Summary of Contents for QB2

Reviews:

Related manuals for QB2

Brands by name

Popular brands