background image

J-PRO-22 Alum Guide Rev 0021622   Page | 1 

 

J-PRO-22 Alum  

                                            

Installation & Start-Up Guide 

No Alum Included in Pump Box  

 

Want larger text?  Click the link to read this online or download the PDF: 

https://www.cleanwaterstore.com/technical/water-treatment-manuals/J-PRO-
22-Alum-Guide.pdf

  

Thank you for purchasing a Clean Water System! With proper 
installation and a little routine maintenance, your system will be 
providing treated water for many years. 

Please review this start-up guide entirely before beginning to 
install your system and follow the steps outlined for best results. 

  

Specifications: 

Pumps 0.1 to 22 gallons of solution per day 

Injects into line pressures up to 110 PSI 

Dual voltage. 110V or 220V, works on either voltage.  

Uses maximum 22 watts of power. 

 

Dimensions:   

5-gallon model: 10” x 10” x 15”. Height including pump is 26” 

15-gallon model: 14.5" wide x 24", height including pump is 35".  

35-gallon model: 18" wide x 33", height including pump is 44". 

 

 
USE FACEMASK, RUBBER GLOVES AND EYE PROTECTION WHEN HANDLING ALUM POWDER. 
 
NOTE ABOUT 220V INSTALLATIONS:  This pump is dual voltage right out of the box and works on 110v OR 220v. 
 
If you plan to install to run on 220v-240v, we recommend cutting off plug and either hard-wiring to 220v circuit OR 
installing a 220v plug-end. 
 

This pump is intended for indoor use, or for outdoors if protected from sunlight and freezing. 

2806-A Soquel Ave Santa Cruz CA 95062    For assistance call: 1-831-462-8500  
Email us: 

[email protected]

     More information online

www.cleanwaterstore.com

  

 

Summary of Contents for J-PRO-22

















Reviews: