Charger operation
The RTIC-2120-WP is fully automatic once installed properly.
The LED indicator lights inform the user of the progress of the
charging cycle and confirm proper connections.
Electrical characteristics
LED indicators
Charging mode: Indicates the state of charge of the battery.
The green Float light indicates the battery is fully charged.
Charging current LEDs indicate amount of current.
AC Power On LED indicates AC power is applied to the
charger.
Charging status LED indicates the output is connected
properly to the battery and is being charged.
Protection modes
Over temperature:
The unit inhibits until it cools off and then
restarts automatically. This is indicated by the AC Power and
Float LEDs flashing. In very high ambient temperatures, it is
possible for the non-auto reset thermal protection to activate.
This is indicated by the AC Power on and 14-20 Amp Charging
Current LEDs flashing. If this occurs, the AC power should be
disconnected and reconnected once the charger has cooled off.
Over voltage:
Activates in the event of a regulation malfunction
and inhibits the charger. An over voltage condition is indicated
by the AC Power On and Fast LEDs flashing. If the over voltage
persists, the factory should be consulted.
Optional relay contacts
Up to four relay contacts are provided depending upon the op
-
tion purchased. The relay specification is available on our web
page. Please observe relay specifications in order to maintain
proper operation.
Optional temperature compensation
The temperature compensation pod can be tie-wrapped to the
charger cable in the immediate vicinity of the battery or wall
mounted. Standard compensation is 15mV-18mV per degree
Celsius per cell or factory programmable upon request.
Please read the entire installation manual before installing
the battery charger. If there are any questions or concerns,
please email us or call our toll-free number given below.
The RTIC-2120-WP is a rugged, waterproof and sophis
-
ticated three state lead-acid battery charger. With a wide
operating temperature range and UL/CSA1236 certifica
-
tion, this product is especially suited for high end industrial
applications and severe environments.
The RTIC-2120-WP is factory programmable to accom-
modate several charging algorithms, an LED display to
indicate status, and optional four relay contacts to indicate
various scenarios. Temperature compensation is imple
-
mented digitally allowing accurate and noise free sensing
up to a distance of 300 feet eliminating problems associ-
ated with conventional analog solutions.
The charging algorithm, LEDs, and relay control signals
are generated by an embedded microcontroller that con-
tains software developed by and proprietary to Chargetek.
The RTIC-2120-WP precisely controls charging voltage
and current to ensure a complete recharge every time.
The charger may be left connected indefinitely to the bat
-
tery, maintaining a full charge.
RTIC-2120-WP
Installation Manual
Optional signal connector
Outline and mounting
Chargetek
409 Calle San Pablo, Unit 104, Camarillo, CA 93012
~ Phone: (866) 482-7930 ~ Fax: (805) 482-7936
www.chargetek.com
LIMITED WARRANTY
For two years from date of purchase, Chargetek Inc. will at its discretion repair or replace for the original consumer, free of
charge, any part or parts found to be defective by Chargetek in workmanship or material. All shipping charges under this
warranty must be paid by the consumer. Proof of purchase is required.
There is no other expressed warranty. Implied warranties, including those of merchantability and fitness for a particular
purpose are limited to two years from the date of purchase. This is the exclusive remedy and consequential damages are
excluded where permitted by law.
SIGNAL
DESCRIPTION
AC Fail
AC < 170VAC
DC High
DC > 15.5VDC
DC Low
DC < 12VDC
Over Temperature
Unit shutdown, automatically restart
PARAMETER DESCRIPTION / CONDITIONS
MIN
NOM
MAX UNITS
V
FSTERM
Fast charge voltage, 25C
14.4
14.5
14.6
VDC
V
FLOAT
Float voltage, I
OUT
< 1.0 A, 25C
13.2
13.4
13.6
VDC
I
FS
Fast charge, V
BATTERY
= 12V
20
21
22
Amps
I
FLTERM
Float charge termination current
3.2
3.4
3.6
Amps
V
AC
RMS AC voltage range
180
220
270
VAC
I
SBY
Standby current, AC off
0.5
ma
Dimensions in inches
