Century Helicopter Products Radikal G30 Manual Download | Manualshive

Page: 1 / 40

background image

Kit Features:

Specifications:

Lightweight yet extremely strong carbon fiber frames.
High gloss large diameter 25mm tail boom with belt drive system.
Blade grips accommodate blades 14mm to 16mm blade roots.
300 mL fuel tank for long engine run time.
Convenient and easy access to spark plug.
Triple bearing supported blade grips and tail blade grips.
Machined center dual ball bearing swashplate for 120 degree CCPM.
Adjustable bell-hiller ratio allows tuning for preferred cyclic response.
Tunable flight characteristics for stability or speed.

Length: 1397mm
Height: 432mm
Width: 260mm
Main rotor diameter: 1580mm
Tail rotor diameter: 282.5mm
Main rotor blades: 690mm-720mm
Tail rotor blades: 95mm

Version 1.00

© 2013 Century Helicopter Products - All rights reserved.

VERSION 2.0

1
2
3
...
»

Summary of Contents for Radikal G30









































Reviews:

No comments

Related manuals for Radikal G30

Brand: Faller Pages: 8

Brand: Faller Pages: 4

Brand: Faller Pages: 4

Brand: Lionel Pages: 28

P-40B Tomahawk exterior

Brand: Eduard Pages: 2

Brand: Innoflight Pages: 67

Smart Bluetooth Robot Car

Brand: Uctronics Pages: 42

Toot-Toot Drivers CustomisablePeople Carrier

Brand: VTech Pages: 11

Tamagochi Friends

Brand: Bandai Pages: 4

Lincoln Logs Big L Ranch

Brand: K'Nex Pages: 8

Zoom Ju 87A interior S.A.

Brand: Eduard Pages: 4

Holiday Tradition Express

Brand: Lionel Pages: 16

Brand: Faller Pages: 8

Brand: THINK GIZMOS Pages: 30

Brand: Eduard Pages: 6

imaginext J2532

Brand: Fisher-Price Pages: 12

TRACKMASTER T0787

Brand: Fisher-Price Pages: 1

Brand: Oregon Scientific Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands