background image

1. INTRODUCTION 

 
This series is a compact and fully pure sinewave line interactive UPS, and it 
designs for critical application and environment, such as desktops, servers, 
workstations, and other networking equipments. This model is available in the 
output ratings of 750, 1000, 1500, 2000, and 3000VA. This series protects 
your sensitive electronic equipments against power problems including power 
sags, spike, brownouts, line noise, and blackouts. 
 
This series designs from two-in-one form factor; it can be placed either in 
Rack 2U or Tower. The front panel of the UPS includes LED indicators and

 

four push buttons (Power Switch, UPS Test/Silence, Configure, and Enter) 
that allow to monitor easily, configuration and control, AC line-in, notification 
of site wiring fault and output load status of the UPS. It also includes four 
LED bar graphic (Load/Battery Level Indication); two status indications (On 
AC, On Battery); five alarm indications (Overload, Over Temperature, Site 
Wiring Fault, Battery Fault, Self Test Failure). A push button from the front 
panel allows silencing of the AC fail alarm and the initiation of the UPS self 
test sequence as well. The UPS case for 750 ~ 2000VA is made of plastic as 
well as 3000VA is made of metal. 
 
This series is powered from the AC mains and supply AC outputs via 
receptacles on the rear panel. Communication and control to the unit is 
available through serial or USB ports located on the rear panel. The serial 
port will support communications directly with a server. The communications 
protocol for the serial ports shall conform to true RS232 interface.     
 
Features: 
 

 

Microprocessor control guarantees high reliability 

 

High frequency design 

 

Built-in boost and buck AVR   

 

User replaceable design for 1500VA or above 

 

Selectable output range and line sensitive 

 

Cold startup capability 

 

Built-in Dry contact/RS-232/USB communication port 

 

SNMP allows for web-based remote or monitoring management 

 

Enable to extend runtime with scalable external battery pack for   

1500VA or above 

 

Overload, Short-circuit, and overheat protection 

 

Rack/Tower 2 in 1 Design   

 

19” rack mount available for all models

Summary of Contents for 1000VA 1500VA









































Reviews: