Central Machinery CENTRAL MACHINERY 98524 Set Up And Operating Instructions Manual Download

Page: 1 / 20

13” PLANER

WITH DUST COLLECTOR

98524

SET UP AND OPERATINg INSTRUCTIONS

Distributed exclusively by Harbor Freight Tools

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS mANUAL.

2008 by Harbor Freight Tools

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Summary of Contents for CENTRAL MACHINERY 98524





















Search results

Summary of Contents for CENTRAL MACHINERY 98524

Reviews:

Related manuals for CENTRAL MACHINERY 98524

Brands by name

Popular brands

Central Machinery CENTRAL MACHINERY 98524, Set Up And Operating Instructions Manual

Search results

Summary of Contents for CENTRAL MACHINERY 98524

Reviews:

Related manuals for CENTRAL MACHINERY 98524

Brands by name

Popular brands