background image

GASOLINE AUGER DRILL

1.5 HP

Model

95346

ASSEMbLy AND OPERAtION INStRUctIONS

Due to continuing improvements, actual product may differ slightly from the product described herein.

cAUtION!

your Warranty Is Voided If:

you do not operate the Auger Drill with the proper 25:1 unleaded fuel/2-cycle oil mix in its fuel tank.  Do not 

run the Engine with an improper fuel mix, low or no fuel mix.  Running the Engine with an improper fuel mix, 

low or no fuel mix, will permanently damage the unit.
you do not operate the Auger Drill with the proper amount of SAE 80-90 gear oil in its Gearbox.  Do not run the 

Auger Drill with low or no gear oil.  Running the Auger Drill with low or no gear oil will permanently damage 

the unit. 

Distributed exclusively by 

Harbor Freight Tools

®

.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

tO PREVENt SERIOUS INjURy, READ AND UNDERStAND 

ALL WARNINGS AND INStRUctIONS bEfORE USE.

Copyright

©

 2006 by Harbor Freight Tools

®

.  All rights reserved.  No portion of this 

manual or any artwork contained herein may be reproduced in any shape or form 

without the express written consent of Harbor Freight Tools.

for technical questions or replacement parts, please call 1-800-444-3353.

Manual Revised 07b, 07e

Summary of Contents for 95346




















Reviews: