background image

Casablanca Fan Co. - Factory Service Department - Technical Library

1

File Name (TBW500ConvertW505.pmd) RAS 05-18-2007

TYPE INFORMATION

APPLIES

SPECIFIC

RELEASE

TECHNICAL INFORMATION

COSMPOLITAN SERIES FANS
CONVERSION  INFORMATION

INSTALLED IN CANOPY

FIELD SERVICE
W-500 RECEIVER
AND TRANSMITTER
AS NEEDED

COSMPOLITAN SERIES

CONVERSION
INFORMATION

DATE : 5-17-2007
TECHNICAL BULLETIN
RELEASE  TB05172007A
W500 TO W505 CONVERSION

CANOPY RECEIVER CUP - INSTALLATION

W-500 CONVERSION TO W-505 RECEIVER AND TRANSMITTER

Page 1 of 13

INFORMATION ONLY

T

he information within this document will help

you when converting  the W-500 Receiver in
the Canopy Receiver Cup as shown (Figure
#1) to W-505 Receiver. Covered is how to
wire and install. 

Also covered, are different

wiring diagrams you might need. The removal
of the canopy trim ring and helpful hints on
how to make the job a little easier, when the
third hand or second person is required.

    New changes have made to both the channel settings and operation of the electronics of the New
W-505 receiver and transmitter. The jumper where removed from both the receiver and transmitter
and dip switches were added only to the transmitter for easy setup. Changing the channel on the fan
is not done by changing the dip switch, but by pressing a series of buttons on the W-505 wall control,
as covered in the Operation section of this technical bulletin.

Convert W500 to W505 - 

Continued

NOTE: Both RECEIVER and TRANSMITER
MUST be replace as a set or this repair will
NOT work.

(Figure #1)

Summary of Contents for W-500














Reviews: