MI146 REV.10 Page 1 of 3
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR
SERIES OKA – INFRARED RADIANT HEATERS
FIRE/EXPLOSION HAZARD WARNING - During operation, take precautions to ensure that
combustible materials are always kept at a safe distance from the radiant energy. This heater is
not intended for use in hazardous areas where flammable vapours, gases or liquids or other
combustibles are present. Remember that objects placed under an infrared heater can take a while
to reach stabilized temperatures. If you are unsure of the suitability of the heater for the intended
application, check with the factory for recommendations. Failure to comply can result in personal
injury and/or property damage.
DESCRIPTION
1.0
The OKA radiant heater is suitable for process heating in
non-hazardous areas protected from rain, snow or splashing, where
heating element temperatures in excess of 1382°F(750°C) will not
present the risk of fire or explosion. This heater is not intended for
use in comfort heating applications.
2.0
The OKA heater is available with metal sheathed, quartz
lamp or quartz tube heating elements. Use heaters with metal
sheathed elements where there is heavy vibration or mechanical
shock. Quartz tube or quartz lamp elements are very fragile and
require extreme care in handling. Heaters utilizing quartz tubes or
quartz lamps are unsuitable for applications in locations where the
risk of heavy vibration or mechanical shock exists.
3.0
To avoid damage in transit, heaters with quartz lamp or
quartz tube elements are shipped with the elements not installed in
the fixture.
4.0
A minimum of handling of the quartz sheath is
recommended since any type of contamination on the sheath may
reduce service life.
INSTALLATION
The system designer is responsible for
the safety of this equipment and
adequate back-up controls and safety
devices must be installed. Failure to
comply could result in personal injury
and/or property damage.
Heaters must be wired by qualified
personnel in compliance with local
codes.
5.0
Verify that the nameplate voltage and wattage are suitable
for use on the available electrical power supply. Do not connect
the heater to an electrical supply voltage other than shown on the
product label.
For metal sheathed heaters, insulation
contamination
or
moisture
accumulation can cause fault to the
element sheath generating arcing and
releasing molten metal. Install proper
ground fault protection to prevent
personal injury and/or property
damage.
6.0
When mounting, maintain a minimum clearance to
combustibles of 15”(381 mm) at sides, 10”(254 mm) at top and
12”(305 mm) at ends.
Heaters with quartz tube or quartz lamp
type heating elements are suitable for
horizontal mounting only. Heaters with
metal sheathed heating elements can
be mounted in any desired position.
7.0
For short circuit protection, heaters must be installed with
proper fast acting fuses or breakers as close as possible to the
amperage draw of the unit(s), in compliance with the local electrical
codes.
380 mm
[15”]
300 mm
[12”]
250
m
m
[10”
]
FIG. 1 – MOUNTING CLEARANCES
CCI Thermal Technologies Inc. 2721 Plymouth Drive, Oakville, ON L6H 5R5 Tel. (905) 829-4422 Fax (905) 829-4430
www.ccithermal.com
ISO 9001:2000
MI148 REV.11.01
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR
SERIES OKB, OKD & OKH – INFRARED RADIANT HEATERS
ISO 9001
FIRE/EXPLOSION HAZARD WARNING - During operation, take precautions to ensure that combustible materials
are always kept at a safe distance from the radiant energy. This heater is not intended for use in hazardous areas
where flammable vapours, gases or liquids or other combustibles are present. Remember that objects placed under
an infrared heater can take a while to reach stabilized temperatures. If you are unsure of the suitability of the heater for
the intended application, check with the factory for recommendations. Failure to comply can result in personal injury
and/or property damage.
1.0
The OKB, OKD & OKH radiant heaters are suitable for
comfort heating use in non-hazardous areas protected from
rain, snow or splashing, where heating element temperatures
in excess of 1382°F(750°C) will not present the risk of fire or
explosion. The heater does not present a safety hazard when
it is installed, operated and maintained in accordance with
these instructions.
2.0
The heaters are available with metal sheath, quartz
lamp or quartz tube heating elements. Use heaters with
metal sheathed elements where there is heavy vibration or
mechanical shock. Quartz tube or quartz lamp elements are
very fragile and require extreme care in handling. Heaters
utilizing quartz tubes or quartz lamps are unsuitable for
applications in locations where the risk of heavy vibration or
mechanical shock exists.
3.0
To avoid damage in transit, heaters with quartz lamp
or quartz tube elements are shipped with the elements not
installed in the fixture.
4.0
A minimum of handling of the quartz sheath is
recommended since any type of contamination on the sheath
may reduce service life.
DESCRIPTION
The system designer is responsible for
the safety of this equipment and adequate
backup controls and safety devices must be
installed. Failure to comply could result in
personal injury and/or property damage.
Heaters must be wired by qualified personnel
in compliance with local codes.
5.0
Verify that the nameplate voltage and wattage are suitable
for use on the available electrical power supply. Do not connect
the heater to an electrical supply voltage other than shown on
the product label.
6.0
Minimum space clearances from combustibles, when
heaters are horizontally mounted and installed, as listed in
Table 1 following.
DESCRIPTION
MI146 REV.10 Page 1 of 3
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR
SERIES OKA – INFRARED RADIANT HEATERS
FIRE/EXPLOSION HAZARD WARNING - During operation, take precautions to ensure that
combustible materials are always kept at a safe distance from the radiant energy. This heater is
not intended for use in hazardous areas where flammable vapours, gases or liquids or other
combustibles are present. Remember that objects placed under an infrared heater can take a while
to reach stabilized temperatures. If you are unsure of the suitability of the heater for the intended
application, check with the factory for recommendations. Failure to comply can result in personal
injury and/or property damage.
DESCRIPTION
1.0
The OKA radiant heater is suitable for process heating in
non-hazardous areas protected from rain, snow or splashing, where
heating element temperatures in excess of 1382°F(750°C) will not
present the risk of fire or explosion. This heater is not intended for
use in comfort heating applications.
2.0
The OKA heater is available with metal sheathed, quartz
lamp or quartz tube heating elements. Use heaters with metal
sheathed elements where there is heavy vibration or mechanical
shock. Quartz tube or quartz lamp elements are very fragile and
require extreme care in handling. Heaters utilizing quartz tubes or
quartz lamps are unsuitable for applications in locations where the
risk of heavy vibration or mechanical shock exists.
3.0
To avoid damage in transit, heaters with quartz lamp or
quartz tube elements are shipped with the elements not installed in
the fixture.
4.0
A minimum of handling of the quartz sheath is
recommended since any type of contamination on the sheath may
reduce service life.
INSTALLATION
The system designer is responsible for
the safety of this equipment and
adequate back-up controls and safety
devices must be installed. Failure to
comply could result in personal injury
and/or property damage.
Heaters must be wired by qualified
personnel in compliance with local
codes.
5.0
Verify that the nameplate voltage and wattage are suitable
for use on the available electrical power supply. Do not connect
the heater to an electrical supply voltage other than shown on the
product label.
For metal sheathed heaters, insulation
contamination
or
moisture
accumulation can cause fault to the
element sheath generating arcing and
releasing molten metal. Install proper
ground fault protection to prevent
personal injury and/or property
damage.
6.0
When mounting, maintain a minimum clearance to
combustibles of 15”(381 mm) at sides, 10”(254 mm) at top and
12”(305 mm) at ends.
Heaters with quartz tube or quartz lamp
type heating elements are suitable for
horizontal mounting only. Heaters with
metal sheathed heating elements can
be mounted in any desired position.
7.0
For short circuit protection, heaters must be installed with
proper fast acting fuses or breakers as close as possible to the
amperage draw of the unit(s), in compliance with the local electrical
codes.
380 mm
[15”]
300 mm
[12”]
250
m
m
[10”
]
FIG. 1 – MOUNTING CLEARANCES
CCI Thermal Technologies Inc. 2721 Plymouth Drive, Oakville, ON L6H 5R5 Tel. (905) 829-4422 Fax (905) 829-4430
www.ccithermal.com
ISO 9001:2000
7.0
For chain mounting, install eye bolts supplied in the
¼-20 drilled and tapped holes located at the top of the cast
aluminumend plates. Use the locking nut to secure the eye bolt
in the casting at the preferred location. Fasten the chains to the
eye bolts and suspend the fixture from the ceiling ensuring that
the minimum clearances shown in Table 1 are maintained.
MI148 REV.11 Page 1 of 3
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR
SERIES OKB, OKD & OKH – INFRARED RADIANT HEATERS
FIRE/EXPLOSION HAZARD WARNING - During operation, take precautions to ensure that
combustible materials are always kept at a safe distance from the radiant energy. This heater is
not intended for use in hazardous areas where flammable vapours, gases or liquids or other
combustibles are present. Remember that objects placed under an infrared heater can take a while
to reach stabilized temperatures. If you are unsure of the suitability of the heater for the intended
application, check with the factory for recommendations. Failure to comply can result in personal
injury and/or property damage.
DESCRIPTION
1.0
The OKB, OKD & OKH radiant heaters are suitable for
comfort heating use in non-hazardous areas protected from rain,
snow or splashing, where heating element temperatures in excess
of 1382°F(750°C) will not present the risk of fire or explosion. The
heater does not present a safety hazard when it is installed, operated
and maintained in accordance with these instructions.
2.0
The heaters are available with metal sheath, quartz lamp
or quartz tube heating elements. Use heaters with metal sheathed
elements where there is heavy vibration or mechanical shock.
Quartz tube or quartz lamp elements are very fragile and require
extreme care in handling. Heaters utilizing quartz tubes or quartz
lamps are unsuitable for applications in locations where the risk of
heavy vibration or mechanical shock exists.
3.0
To avoid damage in transit, heaters with quartz lamp or
quartz tube elements are shipped with the elements not installed in
the fixture.
4.0
A minimum of handling of the quartz sheath is
recommended since any type of contamination on the sheath may
reduce service life.
INSTALLATION
The system designer is responsible for the
safety of this equipment and adequate back-
up controls and safety devices must be
installed. Failure to comply could result in
personal injury and/or property damage.
Heaters must be wired by qualified personnel
in compliance with local codes.
5.0
Verify that the nameplate voltage and wattage are suitable
for use on the available electrical power supply. Do not connect
the heater to an electrical supply voltage other than shown on the
product label.
6.0
Minimum space clearances from combustibles, when
heaters are horizontally mounted and installed, as listed in Table 1
following.
7.0
For chain mounting, install eye bolts supplied in the ¼-20
drilled and tapped holes located at the top of the cast aluminum
end plates. Use the locking nut to secure the eye bolt in the casting
at the preferred location. Fasten the chains to the eye bolts and
suspend the fixture from the ceiling ensuring that the minimum
clearances shown in Table 1 are maintained.
UL
CSA
Table 1
OKB, OKD & OKH
OKB
OKD &
H
K
O
L
N
C
L
S
U
A. From the nearest w all
24"(610 mm)
15"(380mm) 10"(254mm)
B. From end of heater to w all
24"(610 mm)
12"(305mm) 39"(1000mm)
C. From the ceiling
24"(610 mm)
15"(380mm) 15"(380mm)
D. From the Floor
72"(1830 mm) 96"(2400 mm)
–
–
E. Betw een heaters
36"(915 mm)
–
–
8.0
For rod mounting ¼”-20 threaded rods of suitable length
are to be installed in place of the eye bolts as in paragraph 7.0
above.
9.0
If flush mounting on a non-combustible surface, be sure to
slot the mounting holes (5/16” x ½” hole) to allow for heater
expansion.
10.0
These heaters are intended to be installed in a maximum
40°C ambient temperature.
For metal sheathed heaters, insulation
contamination or moisture accumulation can
cause fault to the element sheath generating
arcing and releasing molten metal. Install
proper ground fault protection to prevent
personal injury and/or property damage.
FIG. 1 – MOUNTING CLEARANCES
A
D
E
B
C
CCI Thermal Technologies Inc. 2721 Plymouth Drive, Oakville, ON L6H 5R5 Tel. (905) 829-4422 Fax (905) 829-4430
www.ccithermal.com
ISO 9001:2000
8.0
For rod mounting ¼”-20 threaded rods of suitable length
are to be installed in place of the eye bolts as in paragraph 7.0
above.
9.0
If flush mounting on a non-combustible surface, be sure
to slot the mounting holes (5/16” x ½” hole) to allow for heater
expansion.
10.0
These heaters are intended to be installed in a maximum
40°C ambient temperature.
For metal sheathed heaters, insulation
contamination or moisture accumulation
cancause fault to the element sheath
generating arcing and releasing molten
metal. Install proper ground fault protection
to prevent personal injury and/or property
damage.
