background image

CALIFORNIA ACCENT LIGHTING, INC.

2820 E. Gretta Lane, Anaheim, CA 92806
ph. 800.921.CALI (2254) | fx. 714.535.7902 | [email protected] | calilighting.com

© CALI. All rights reserved. CALI reserves the right to make changes or withdraw specifications without prior notice.

1 / 29 / 2021 / Rev 2

Page 1 of 16

Overview

ALS

500T-RMW-MI

INSTALLATION INSTRUCTIONS

IMPORTANT NOTICE:

 

VERIFY CORRECT LUMINAIRE WAS RECEIVED WITH 

CORRECT COLOR TEMPERATURE, VOLTAGE, AND WATTAGE BEFORE CUTTING OR 
INSTALLING. CALI WILL NOT BE RESPONSIBLE IF INCORRECT LUMINAIRE IS INSTALLED.

READ ENTIRE GUIDE BEFORE STARTING INSTALLATION

• Electric Hammer Drills (optional)    
• 14.4 to 28 Volt Cordless Drills          
• Phillips Bits - Sufficient Quantity    
• Utility Knife
• Electrical Cords                   
• Marker 
• Wire Strippers

• Long Nose Pliers
• Drill Bits - Concrete or Wood
• Electrical Three Ways
• Safety Glasses
• Measuring Tapes
• Chalk Line 

             

• ALS500T-RMW can be mounted to concrete, wood, or metal using proper
   mounting hardware.
• Ensure surface material can support the weight of the luminaire.

ELECTRICAL

INSTALLATION RECOMMENDATIONS

INSTALLATION TOOL REQUIRED

• ALS500T-RMW requires a remote driver. The driver may be mounted on
   top of the luminaire or in a remote location.
• Drivers are 120V - 277V (UNV) Input Voltage and 24VDC Output Voltage
• To calculate driver size, determine Watts per Foot.
   

Example:

 4W per Foot

• Determine Length in Feet.
   

Example:

 20’

• To calculate Load, Multiply Watts per Foot x Length in Feet
   

Example:

 4W x 20’= 80W. The Load of the driver is 80 Watts.

• Maximum load for a Class 2 low voltage luminaire is 96 Watts

END VIEWS (With Mud-In Ceiling Trim)

1.85”

7.31”

1.38”

7.0”

3.27”

3.60”

Max.

Hanging Bracket Assembly

(ALS500T-RMW-HB)

1.38”

5.27”

X (Specified Length)

7.31”

1.85”

Aircraft Cable Assembly

(ALS500T-RMW-AC)

• Indirect lighting
• 24 Volts DC for easy and safe installation 
• Long life, energy efficient LEDs
• Available in 4 Watts up to 12 Watts Per Foot 
• Can be ordered to specific lengths for when exact dimensions are known 
   

Example:

 10 x 10’6” (product is shipped in 8’ max luminaires)

• Available for indoor (DRY) and (DAMP) rated installations

PRODUCT INFORMATION

CONTENTS

DESIGN GUIDELINES

Page 2

HANGING BRACKET MOUNTING

Page 3 - 5

AIRCRAFT CABLE MOUNTING

Page 6 - 9

REFLECTIVE FILM

Page 14

TROUBLESHOOTING

Page 15

CARE & MAINTENANCE

Page 16

FEATURES

APPLICATIONS

Indirect Lighting

LENS

Clear

LENGTH

Built to Order (± 0.25” Tolerance)

CONSTRUCTION

Aluminum Extrusion

FINISH

White Powder Coated

DRIVER

Remote

WEIGHT

4.50 lbs per foot

MOUNTING

Mounting Brackets or Aircraft Cable

LISTING

Dry or Damp Location
UL1598, CSA C22.2#250.0
UL8750, CSA250
UL2108, CSA C22.2 #9

TEMPERATURE 

RATINGS

Operating / Startup:

 -20° to 48°C (-4° to 120°F)

Storage:

 -40° to 76°C (-40° to 170°F)

Summary of Contents for alumLEDs ALS500T-RMW-MI

















Reviews: