background image

Carpet Knife Xti

Assembly Manual

and Parts list

Calandra Racing Concepts, Inc.

6785 Martin Street ~ Rome, NY U.S.A. 13440

Tel + Fax 315-338-0867

www.teamcrc.com ~ [email protected]

CRC “Xti” 1:12th

competition kit

for 1s lipo cells

2012 IFMAR

World A-Finalist!

2 cars!

Part #3210

True

“inline”

design.

Multiple

cell p

ositions;

transverse

and inline.

(w/ o

ptional

transverse

kit)

Features CRC Slider

rear pods! No inserts,

no set positions. Just

place desired ride

shim under the car and

drop the axle!

Xti Features

** CRC Encore bladder shock.

** Servo and speedo mounted centerline.

** “True inline” battery placement w/ full size 1s battery.

** CRC molded spur gear w/ 3/32 diff balls. Less rotating weight!

** Aerospace grade 100% pure carbon fiber chassis and structure parts.

**

multiple battery placement, transverse pack (w/optional kit) and inline.

** Proven Pro-Strut front end with symmetrical comp optional roll centers

**

Revolutionary CRC “Slider” rear pod, no inserts, adjusters or detent axle positions.

New

NEW!

Xti Features

** CRC Encore bladder shock.

** Servo and speedo mounted centerline.

** “True inline” battery placement w/ full size 1s battery.

** CRC molded spur gear w/ 3/32 diff balls. Less rotating weight!

** Aerospace grade 100% pure carbon fiber chassis and structure parts.

** Proven Pro-Strut front end with symmetrical comp optional roll centers

**

Revolutionary CRC “Slider” rear pod, no inserts, adjusters or detent axle positions.

NEW!

**

multiple battery placement, transverse pack (w/optional kit) and inline.

New

Calandra Racing Concepts

6785 Martin Street ~ Rome, NY 13440 ~ Tel 315-338-0867 ~ Fax 315-217-4204 ~

www.teamcrc.com [email protected]

tires, servo + servo saver

not included. Shown below;

car w/ optional transverse kit.

8

6

0 0 7 3 4 0 3 2 1 0

Summary of Contents for Carpet Knofe Xti

















Reviews: