background image

1

TM

Safety Precautions

1.

 Read this entire Owners Manual before operating this 

spreader.

2.

 Read all safety decals on the spreader before operating. 

3.

 Check to make sure all safety guards are securely 

mounted into place before operating this spreader. 

4.

 Verify that all personnel are clear of the spreader spray 

area before starting or operating this spreader. 

5.

 Do not over-load your vehicle beyond payload limits. If 

there are any questions, contact the vehicle manufacturer. 

6.

 Do not adjust, clean, lubricate or unclog material jambs 

without first turning off the spreader. 

7.

 Do not climb on or in the spreader during operation. Do not 

ride on the spreader while the vehicle is in motion. 

8.

 Make sure the spreader is securely fastened to the vehicle 

in accordance with this manual. 

9.

 Do not operate a spreader that is in need of maintenance 

or repairs. 

10.

 Batteries normally produce explosive gases which can 

cause personal injury. Always disconnect the battery before 
removing or replacing electrical components. 

11.

 Do not leave unused material in hopper. Material can 

freeze or solidify, causing spreader to not work properly, and/
or damage the unit. Empty and clean after each use.

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Installation Instructions

SaltDogg

® 

Electric Drive 

Poly Hopper Spreader 

3.0 cubic yards

starting with Serial Number 00500

—continued inside

Table of Contents 

General Information  ........................................1 
Safety Precautions  ...........................................1 
Warranty Information  ......................................2 
Installation Instructions  ............................. 2-4 
Spreader Operation  ..........................................5 
Spreader Maintenance  ....................................5 
Repair Parts & Drawings  ...........................6-10 

General Information 

Overall Length: 123.7 inches 
Overall Width: 49.6 inches 
Overall Height: 52.7 inches 
Empty Weight: 945 lbs 
Capacity Struck: 3.0 cu. yd. 

Vehicle Requirements 

Trucks with minimum GVWR 13,000 lbs.
150 AMP or higher alternator is recommended. 

Average Material Weights 

Materials to use  

Weight (pounds per cubic yard)

Fine Salt-Dry  

2,250

Coarse Salt-Dry  

1,431

Sand Coarse-Dry 

2,565

Note:

 To calculate the total spreader weight (including ice 

control material), add the empty spreader weight plus the ice 
control material and spreader accessories. 

CAUTION

Do not overload vehicle beyond the vehicle’s GVWR or GAWR. 

Check vehicle’s load rating certification sticker for maximum 

vehicle capacity.

WARNING

 

Improper installation and operation could cause personal 

injury, and/or property damage. Observe the following Safety 

Precautions before, during and after operating this spreader. 

By following these precautions and common sense, possible 

injury to persons and potential damage to this machine may be 

avoided.

CAUTION

It is recommended to install Backup Alarm on trucks to be up 

fitted with spreaders.

Summary of Contents for SaltDogg SHPE3000









Reviews: