background image

PAGE  1 

PSTICK80 

Stick Welder with TIG Option 

Assembly & Operating Instructions 

 

   

 
 
 

 

 

 

 

 

 

 

READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. 

This manual provides important information on proper operation & maintenance. Every effort has been made to 

ensure the accuracy of this manual. These instructions are not meant to cover every possible condition and situation 

that may occur. 

We reserve the right to change this product at any time without prior notice. 

 

 
IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE, DO NOT 
OPERATE THIS PRODUCT!  
 
HAVE QUESTIONS OR PROBLEMS? DO NOT RETURN THIS PRODUCT TO THE RETAILER - 
CONTACT CUSTOMER SERVICE. 

If you experience a problem or need parts for this product, visit our website http://www.buffalotools.com  

or call our customer help line at 

1-888-287-6981 

Monday-Friday, 8 AM - 4 PM Central Time.  

A copy of the sales receipt is required. 

 

FOR CONSUMER USE ONLY – NOT FOR PROFESSIONAL USE. 
KEEP THIS MANUAL, SALES RECEIPT & APPLICABLE WARRANTY FOR FUTURE REFERENCE.

 

 

CALIFORNIA PROPOSITION 65 WARNING

:  This product m ay contain chem icals, including 

lead, know n to the S tate of C alifornia to cause cancer and birth defects or other reproductive 
harm . W ash hands after handling. 

 

 
 

Summary of Contents for PSTICK80

















Reviews: