background image

 

 

 

 

 

 
 
 
 
 
 
 
 

www.btigauges.com

 

TFT CAN Bus Gauge for 

Plug and Play Installation Manual

Notice:

  

This product is intended for Off

Never take your eyes off of the road

If you are uncomfortable

this device installed by a competent shop.

** Notice!  This device should be configured by competent personnel.  

Raising the BOOST too much or reducing

have severe consequences. 

control of your vehicle

 

 

 

 

 
 
 

www.btigauges.com

 

 
 

CAN Bus Gauge for MoTeC M1 

Plug and Play Installation Manual 

Doc version 1.0 

This product is intended for Off-Road use only.

Never take your eyes off of the road while using this device.

If you are uncomfortable with wire termination, please have 

device installed by a competent shop.

 

 
 
 

** Notice!  This device should be configured by competent personnel.  

Raising the BOOST too much or reducing the Traction Control

have severe consequences.   You could blow your engine and or lose 

control of your vehicle** 

 
 
 
 
 

 

Road use only. 

while using this device. 

termination, please have  

device installed by a competent shop. 

** Notice!  This device should be configured by competent personnel.  

the Traction Control too much can 

You could blow your engine and or lose 

Summary of Contents for MoTeC M130











Reviews: