BURN HAZARD
RISK OF BURN OR SERIOUS INJURY.
HOT SURFACES (GREATER THAN 150°F / 65°C).
DO NOT LEAVE UNATTENDED.
Lights may become extremely hot (more than 150°F / 65°C) when left on for more
than five minutes and may become too hot to touch safely. While on do not leave
unattended. Do not set the light face (lens) down when turned on. Do not handle the
light until it has cooled.
This light is extremely bright. Do not look directly into the light or shine it in
someone’s eyes.
Do not hold the lens or bezel against any portion of the human body. Do not place
headlamp against combustible material or any material that can be damaged by heat.
Always use with adequate ventilation.
BATTERY BURN HAZARD
RISK OF BURN OR SERIOUS INJURY.
Never open a battery, place it in a fire, expose it to heat above 212°F (100°C),
expose its contents to water, put it in backwards, or mix it with other battery types.
Any of these actions can result in an explosion and/or leaking, causing personal
injury or property damage. Dispose of all batteries properly in accordance with
environmental regulations.
CHOKING HAZARD
SMALL PARTS. NOT FOR CHILDREN UNDER 3 YEARS.
Browning lights are not toys. They are high performance lighting tools that contain
batteries and small parts. Use only under adult supervision. Failure to follow this
warning could result in serious injury to the child.
Keep all batteries out of reach of infants and children. Do not allow infants and children
to play with batteries. Do not place batteries in the nose, ears or mouth. If swallowed
they may become a choking hazard and/or may cause electrical and/or chemical burns
in the mouth or in the digestive tract.
If any battery is swallowed, do not induce vomiting. Immediately contact your
physician, the Poison Control Center at 1-800-222-1222, your local health care
center or emergency care center, or the National Button Battery Ingestion Hotline
at 1-202-625-3333.
OPERATION
The Range headlamp is powered by one non-rechargeable AA battery (included). Do
not use other types of batteries. Do not attempt to recharge non-rechargeable batteries.
To insert or remove batteries, open the battery compartment by pulling upward on the
flat tab on the top of the headlamp that is located near the rear edge.
When installing a battery, place the battery as shown on the diagram inside
the compartment.
Close the battery compartment. You should feel and hear the flat tab click into place
when it is fully closed.
To turn the headlamp on, push down with your fingertip on the main switch located on
top of the light where the Browning logo is located.
There are two different operating mode/settings with this headlamp:
1. High/Wide Angle
2. Low/Wide Angle
To cycle through the operating modes/settings, press the main switch repeatedly until
you reach the desired setting.
This headlamp has a Quick Off feature. When the light has been on any setting for more
than three seconds, the light will turn off the next time the main switch is pushed.
This headlamp has an Electronic Battery Lock-Out mode. By using the main switch,
the battery can be locked out so the light will not turn on accidentally.
When the light is off, hold the main switch down for three seconds to activate the
Battery Lock-Out mode. When the Battery Lock-Out mode is activated the light will blink
three times. If you now press and release the main switch the light will not turn on. The
light will blink once to indicate that the battery still has a usable charge and that it is in
Battery Lock-Out mode.
To disengage the Battery Lock-Out mode, hold the main switch
down for three seconds. The light will then blink three times to
indicate it is no longer in Battery Lock-Out mode.
This headlamp has a low battery indicator. When the battery
reaches 20% capacity remaining or less, the light will flash five
times and return to the setting it was on. When this happens, it is
time to replace the battery.
MULTI-DIRECTION CLIP
This headlamp is shipped with the head strap
attached. To attach the clip, first remove the
head strap by pulling it through the two slots on
either end of the head plate (Figure 1).
There are four options for positioning the clip,
depending on how the headlamp is to be used
(Figure 2). To attach the clip, line up the two
center tabs on the clip with the square hole in
the head plate and click it into place (Figure 3).
To remove the clip, push the tabs toward the
center of the square opening in the head plate.
Attach the head strap to the head plate by sliding
the head strap through the slots on either end of
the head plate.
MAINTENANCE
Remove the battery when storing for long
periods of time.
If you have questions, call Browning Customer
Service: 800-333-3288.
RANGE
TM
1AA HEADLAMP WITH WIDE ANGLE TECHNOLOGY
INSTRUCTIONS
Drop-tested onto concrete from
1m without functional damage.
1m
FL 1 STANDARD
LOW
HIGH
Water resistant
28m
4h
175
LUMENS
12h
22
LUMENS
10m
Figure 1
Figure 2
Figure 3
SLOT
HEAD
STRAP
CLIP
CLIP
HEAD PLATE
CENTER TABS
SLOT
HEAD PLATE
