background image

GWH 425 HNO OUTDOOR MODEL

For exterior use only

Electronic Ignition
Suitable for heating potable water only - Not approved for space heating purposes

GWH-425-HNO-N - Natural Gas
GWH-425-HNO-L - Liquefied Petroleum (LP) Gas

71

47

14

U

S

 (0

5.

12

) A

L

Warning: 

If  the  information  in  this  manual  is  not

followed  exactly,  a  fire  or  explosion  may  result
causing property damage, personal injury or death.
Do  not  store  or  use  gasoline  or  other  flammable
vapor and liquids in the vicinity of this or any other
appliance.
Improper installation, adjustment, alteration, service
or  maintenance  can  cause  injury  or  property
damage.  Refer  to  this  manual.  For  assistance  or
additional  information  consult  a  qualified  installer,
service agency or the gas supplier.
In  the  Commonwealth  of  Massachusetts  this
product  is  approved  only  for  seasonal  use.
Installation  must  be  performed  by  a  licensed
plumber or gas fitter.
Upon  completion  of  the  installation,  these
instructions  should  be  handed  to  the  user  of  the
appliance for future reference.

What to do if you smell gas

• Close gas valve.
• Do not try to light any appliance.
• Do  not  touch  any  electrical  switch;  do  not  use  any

phone in your building.

• If  you  cannot  reach  your  gas  supplier,  call  the  fire

department.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

Installation  and  service  must  be  performed  by  a
qualified installer, service agency or the gas supplier.

Summary of Contents for Pro Tankless GWH-425-HNO-L


























Reviews: