background image

520 HN

Flow Modulated with Hydro-generated Ignition

Suitable for heating potable water only - Not approved for space heating purposes 

(Intended for variable flow applications with steady cold water inlet temperatures)

520-HN-N
520-HN-L

6

 7

2

0

 6

4

4

 9

4

2

 (

2

0

1

0

/0

9

U

S

Warning: 

If  the  information  in  this  manual  is  not

followed  exactly,  a  fire  or  explosion  may  result
causing property damage, personal injury or death.
Do  not  store  or  use  gasoline  or  other  flammable
vapor and liquids in the vicinity of this or any other
appliance.

Improper  installation,  adjustment,  alteration,
service  or  maintenance  can  cause  injury  or
property  damage.  Refer  to  this  manual.  For
assistance  or  additional  information  consult  a
qualified  installer,  service  agency  or  the  gas
supplier.
In  the  Commonwealth  of  Massachusetts  this
product must be installed by a licensed plumber or
gas fitter.

Upon  completion  of  the  installation,  these
instructions  should  be  handed  to  the  user  of  the
appliance for future reference.

What to do if you smell gas

• Close gas valve. Open windows.

• Do not try to light any appliance.

• Do  not  touch  any  electrical  switch;  do  not  use  any

phone in your building.

• Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire 

department.

• Installation  and  service  must  be  performed  by  a

qualified installer, service agency or the gas supplier.

Summary of Contents for 520-HN-L





























Reviews: