background image

INDOOR MODEL Flow Modulated with Standing pilot

330 PN

Warning: 

If the information in this manual is not followed exactly, a fire or 

explosion may result causing property damage, personal injury or death.

Do not store or use gasoline or other flammable vapor and liquids in the vicinity 

of this or any other appliance.

Improper installation, adjustment, alteration, service or maintenance can 

cause injury or property damage. Refer to this manual. For assistance or addi-

tional information consult a qualified installer, service agency or the gas sup-

plier. In the Commonwealth of Massachusetts this product must be installed 

by a licensed plumber or gas fitter.

Upon completion of the installation, these instructions should be handed to 

the user of the appliance for future reference.

What to do if you smell gas

Close gas valve. Open windows.

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the 
gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, ser-

vice agency or the gas supplier

330-PN-N - for use with Natural Gas / 330-PN-L - for use with Liquefied Petroleum (LP) Gas

6 720 644 951 (2014/11) US

Suitable for heating potable water only - Not approved for space heating purposes 
(Intended for variable flow applications with steady cold water inlet temperatures)

Summary of Contents for 330-PN-L





































Reviews: