background image

This appliance can be used by children aged from 8 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved. Children shall not

play with the appliance. Cleaning and user maintenance shall not be made by

children without supervision.

The unit should be isolated from the electricity supply before removal of any covers. Great care must be
employed when working with high pressure carbon dioxide, and in no cases should the maximum
operating pressure of 0.4MPa (4 bar) be exceeded.

The appliance is not suitable for installation in an area where a water jet could be used.
The appliance has to be placed in a horizontal position

WARNING: Keep ventilation openings in the appliance enclosure or in the built-in structure clear of
obstruction.

 

WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.

 

WARNING: Do not locate multiple portable socket-outlets or portable power supplies at the rear of the
appliance.

This appliance is intended to be used in household and similar applications such as:-

Staff kitchen areas in shops, offices and other working environments
Farm houses and by clients in hotels, motels and other residential type environments
Bed and breakfast type environments
Catering and similar non-retail applications

A-weighted emission sound pressure level is below 70 dB(A)

Release date 04.02.2022

T2 Install & Operation

Manual

Safety 

Summary of Contents for T2







































Reviews: