![background image](http://html.mh-extra.com/html/bobrick/contura-series/contura-series_instruction-for-installation-and-maintenance_2781838001.webp)
INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE
Bobrick ConturaSeries
®
Model B-4112 Surface-Mounted Soap Dispenser
INSTALLATION:
Lavatories:
Locate dispenser so that spout will be
over the lavatory
. Allow a minimum of
4'' (100mm) clearance between top of dispenser and bottom of any shelf, cabinet, or other
projection to provide enough space to fill dispenser conveniently.
To ATTAch wALL pLATe wiTh screws,
place screws in the three holes provided.
The surface on which unit is to be mounted determines type of screws required for best
installation.
For plaster or dry wall on studs,
provide concealed backing and secure dispenser wall
plate with mounting screws furnished by manufacturer. Backing must comply with local
building codes.
For hollow tile partitions
and other instances where applicable, use 1/8'' (3mm) round-
head toggle bolts.
For brick, concrete, or solid tile walls,
use screws furnished with #8 (4mm) fiber plugs
or provide 1/8'' (3mm) toggle bolts or expansion bolts.
TO MOUNT DISPENSER:
1. open filler-top by inserting BobKey (24-17) into slot of filler-top and then sliding latch to the left. Lift up filler-top.
2. Using screwdriver as shown (see Figure 1), loosen locking-screw (A).
3. position dispenser so that edges of back plate (B) fit into grooves of wall plate and then press dispenser down into place (see Figure 2).
4. Tighten locking-screw against washer. Dispenser locks into place when point of locking-screw is lodged under lug (c) of wall plate
(see Figure 2).
CAUTION:
Failure to tighten screw securely may cause dispenser to leak when filled above this point.
5. close and lock filler-top by reversing operation in step 1.
MAINTENANCE:
1. To fill dispenser, open filler-top by inserting BobKey (24-17) into slot of filler-top and then sliding latch to the left. Lift up filler-top.
Fill dispenser.
To Prevent corrosion, use only chloride-free pH-neutral liquid soaps.
close filler-top and relock by inserting
BobKey into filler-top slot and sliding latch to the right.
NOTE:
Bobrick liquid soap dispensers are designed to dispense commercially marketed all-purpose hand soaps
including liquid and lotion soaps, synthetic detergents, and antibacterial soaps containing PCMX and /or Triclosan.
Bobrick soap dispensers are not designed to dispense alcohol-based hand sanitizers or iodine-based surgical soaps.
2. clean equipment operates better, lasts longer, and requires less maintenance. wipe the unit daily, including the spout, using a
damp cloth. Use only water-soluble cleaners.
Never use abrasive cleaners
. Avoid allowing cleaning liquids to collect behind unit.
periodically, remove unit from wall to clean back. refer to technical bulletin TB-21 for further information.
3. periodically clean the dispenser by pumping warm water mixed with soap from the dispenser through the vessel and valve to flush
out contaminants or dried soap residue.
Never use abrasive cleaners.
4. if the soap valve fails to operate satisfactorily, the problem may be caused by dried soap or dirt clogging the spout or the soap
valve. To reMeDY: clean spout with end of BobKey and/or flush the dispenser as described above.
5. Do not disassemble the soap valve. NoTe: if for any reason the valve becomes nonfunctional, a new soap valve replacement kit
(part No. 4112-79) must be ordered.
7''
180mm
9/16''
15mm
6-1/8''
155mm
A
C
B
FIgURE 3
FIgURE 2
FIgURE 1
continued
. . .