![background image](http://html.mh-extra.com/html/bobrick/b-3942/b-3942_instructions-for-replacing_2781811001.webp)
In the United States: BOBRICK WASHROOM EQUIPMENT, INC.
New York: 200 Commerce Drive, Clifton Park, NY 12065-1350 • Tel: (518) 877-7444 • Fax: (518)-877-5029
Los Angeles: 6901 Tujunga Ave, North Hollywood, CA 91605-6213 • Tel: (818) 982-9600 • Fax: (818)-503-9287
or email [email protected]
In Canada: BOBRICK WASHROOM EQUIPMENT COMPANY
45 Rolark Drive, Scarborough, Ontario M1R 3B1 •
Eastern Canada: Tel: (877) 423-6555 • Fax: (877) 423-8555
•
Western Canada: Tel: (877) 423-6444 • Fax: (877) 423-8444 or email [email protected]
© 2019 by Bobrick Washroom Equipment, Inc.
Form No. 3944-69 Revised 9/16/19 Printed in U.S.A.
INSTRUCTIONS FOR REPLACING 3944-52, FOLDED TOWEL DISPENSER MODULE
BOBRICK MODELS B-3942, B-3944, 3947, AND 813061 CONVERTIBLE PAPER TOWEL DISPENSER AND WASTE RECEPTACLE
Upper Left Side
Keyhole Slot
3981-25 Carriage Bolt
3981-24 Hex Nut Lock
(Mounting Hardware)
Folded Towel
Dispenser Module
Hinge Pin
Cabinet
3981-25 Carriage Bolt
3961-24 Washer Lock Nut
Left Side Upper Keyhole Slot
REMOVING EXISTING FOLDED TOWEL DISPENSER MODULE
1. Unlock and open the door of the Folded Towel Dispenser
Module and remove any paper towels.
Remove door by
removing the hinge pin.
CAUTION
: If door is not removed special care should be
taken to prevent door from swinging when removing last
bolt and causing Module to fall out of cabinet.
2. Loosen but do not remove the four 3961-24 Washer Lock Nuts
located on the left back and right side of the Modular Housing
Assembly until the 3961-25 Carriage Bolt can be moved. The
3961-24 Hex Lock Nut should not be removed from the
3961-25 Carriage Bolt, ensuring that the Carriage Bolt will not
fall into the wall cavity. (See Figure 1)
3. Hold the Housing in place with one hand.
4. Remove the mounting hardware, the 3961-25 Carriage Bolt
with the 3961-24 Washer Lock Nut, by sliding them toward the
hole until the head of the carriage bolt can move through the
round portion of the keyhole slot. Put aside, four places.
5. Carefully remove the housing from the cabinet by sliding it
down past the lower door stop and then rotating out from the
bottom.
INSTALLING NEW FOLDED TOWEL DISPENSER MODULE
1. Carefully insert the Folded Towel Dispenser Module (without
the door) under and behind the lower door stop in the cabinet
until it touches the cabinet flanges. Slide up keeping the right
side of the housing parallel with the right side of the cabinet
supporting it from underneath with both hands. Make sure to
keep the back of the housing against the back flanges of the
cabinet and position the module so that the keyhole slots line
up. (See Figure 2)
2. Insert one set of mounting hardware, the 3961-25 Carriage
Bolt with the 3961-24 Washer Lock Nut, into the round
portion of the upper left side keyhole slot with the head of
the 3961-25 Carriage Bolt going in first. Position the square
shoulder of the 3961-25 Carriage Bolt so that it is parallel
with the straight sides of the keyhole slot and slide the entire
assembly as far over as it will go. The square shoulder of the
3961-25 Carriage Bolt should be in contact with the end of the
rectangular slot in the flange to ensure proper seating of the
mounting hardware. (See Figures 3 & 4).
3. Tighten down the 3961-24 Washer Lock Nut. The mounting
hardware should not move when tugged. Do Not overtighten
the washer lock nuts.
4. Install the rest of the mounting hardware as described in steps
2 & 3 for the other keyhole slots.
5. Install the door using the hinge pin provided.
NOTE: Waste capacity of these units can be changed by
ordering Bobrick part numbers:
367-60 (12-Gallon Waste Receptacle Module)
368-60 (18-Gallon Waste Receptacle Module)
313061-8 (6-Gallon Waste Receptacle Module)
Figure 1
Figure 2
Figure 3
Figure 4
TOOL REQUIRED TO REMOVE LOCK NUT
TOOL NAME
TOOL SIZE
Nut Driver
3/8"
or
Socket Wrench with 3" minimum extension
3/8"