◈
Information
This installation guide contains only simple information required for the installation of
the product. Refer to the User’s Manual in the CD that is shipped with the product for
detailed instructions for installation. The contents contained in the CD are as follows.
1. Manual: User’s Manual, Code Table, Control Commands
2. Driver: Windows Driver, OPOS Driver
3. Utility: Logo Download Tool
We at Bixolon Co., Ltd. constantly strive to improve product functions and quality. To
do this, the specifications of our product and the contents of the manual may change
without prior notice.
◈
Components
SRP-350/352plusIII
Cable Cover
Roll Paper
Procuct Installation CD
Procuct Installation CD
Procuct Installation CD
CD
AC/DC Adaptor
Power Cord
Installation Guide
◈
Cable Connection
1. Turn off the printer and ECR (host computer).
2. Connect the power cord to adaptor, and connect the adapter to the power connector
of the printer.
3. Check the type interface located at the back of the printer (Serial, Parallel, Ethernet,
USB, Powered USB, Wireless LAN, Bluetooth) and connect proper cable.
4. Connect the drawer kick-out cable to the drawer kick-out connector located on the
underside of the printer.
※
Do not use an adapter that was not supplied with the printer.
◈
Installing Paper Roll
1. Press the Cover-Open button to open the
cover.
2. Insert new roll paper in the correct direction.
3. Pull the paper out slightly and close the
cover.
※
Note
Hold down the center of the cover firmly when
closing the cover so that the paper maintains
close contact with the roller.
Printing quality may not be optimum if
recommended paper is not used.
(Refer to the User's Manual.)
◈
Paper Jam
(Refer to 1-6 in User Manual)
1. Turn the printer off and on, open the cover, and remove the paper.
2. If the cover cannot be opened, turn off the printer, separate the cover-cutter, and try
to turn the auto cutter knob to open the cover.
◈
Using Control Panel
•
Power (Indicator Lamp)
Green light will be on when power is supplied to printer.
•
Error (Indicator Lamp)
Red light will be on in various error conditions such as out of paper,
cover open, etc.
•
Paper (Indicator Lamp)
Red light will be on when there is no paper or paper almost runs out. If
this light keeps blinking, it means that the printer is in self-test standby
state or waiting for macro execution.
•
Feed (Button)
Press this button to feed the paper out. Hold down this button to feed
out the paper continuously.
◈
Setting DIP Switches
DIP switch settings should be changed when the printer power is turned off. Any changes made
while printer power is on are not recognized.
1. Serial Interface Settings
• DIP Switch 1
Switch
Function
ON
OFF
Default
1-1
Auto Line Feed
Enabled
Disabled
OFF
1-2 Flow
Control XON/XOFF DTR/DSR
OFF
1-3 Data
Length
7-bit
8-bit OFF
1-4 Parity
Check
Yes
No OFF
1-5
Parity Selection
EVEN
ODD
OFF
1-6
Baud Rate Selection (bps)
Refer to the following Table 1
OFF
1-7
ON
1-8
OFF
• DIP Switch 2
Switch
Function
ON
OFF
Default
2-1
Reserved
-
-
OFF
2-2
Reserved
-
-
OFF
2-3
Internal Bell Control
Disabled
Enabled
OFF
2-4
Auto Cutter Selection
Disabled
Enabled
OFF
2-5
Printing Density
Refer to the following Table 2
OFF
2-6
OFF
2-7
Near End Sensor Control
Disabled
Enabled
OFF
2-8
Auto External Buzz
Enabled
Disabled
OFF
2. Parallel / USB / Ethernet / Wireless LAN / Powered USB interface settings
• DIP Switch 1
Switch
Function
ON
OFF
Default
1-1 Auto
Line
Feed
Enabled
Disabled
OFF
1-2
Reserved
-
-
OFF
1-3
Reserved
-
-
OFF
1-4
Reserved
-
-
OFF
1-5
Reserved
-
-
OFF
1-6 Reserved
-
- OFF
1-7
Reserved
-
-
ON
1-8
Reserved
-
-
OFF
• DIP Switch 2
Switch
Function
ON
OFF
Default
2-1 Reserved
-
- OFF
2-2 Reserved
-
- OFF
2-3
Internal Bell Control
Disabled
Enabled
OFF
2-4
Auto Cutter Selection
Disabled
Enabled
OFF
2-5
Printing Density
Refer to the following Table 2
OFF
2-6
OFF
2-7
Near End Sensor Control
Disabled
Enabled
OFF
2-8
Auto External Buzz
Enabled
Disabled
OFF
3. Bluetooth Interface settings
• DIP Switch 1
Switch
Function
ON
OFF
Default
1-1 Auto
Line
Feed
Enabled
Disabled
OFF
1-2
Reserved
-
-
OFF
1-3 Reserved
-
- OFF
1-4 Reserved
-
- OFF
1-5 Bluetooth
mode
iOS
Normal OFF
1-6 Reserved
-
- OFF
1-7
Reserved
-
-
ON
1-8 Reserved
-
- OFF
• DIP Switch 2
Switch
Function
ON
OFF
Default
2-1 Reserved
-
- OFF
2-2
Reserved
-
-
OFF
2-3
Internal Bell Control
Disabled
Enabled
OFF
2-4
Auto Cutter Selection
Disabled
Enabled
OFF
2-5
Printing Density
Refer to the following Table 2
OFF
2-6
OFF
2-7
Near End Sensor Control
Disabled
Enabled
OFF
2-8
Auto External Buzz
Enabled
Disabled
OFF
Printer Installation Guide & Safety Guide
KN04-00137A (Rev.1.0)
THERMAL PRINTER SRP-350/352plusIII
Power Cord
Ethernet
Cable
Interface Cable
(Serial/Parallel/Powered USB/
Wireless LAN/Bluetooth)
Adaptor
Drawer Kick-out
connector
Power
Connector
Interface Connector
USB
Cable
Drawer Kick-out
Cable
