background image

Dichiarazione di conformità sintetica

 

Ai sensi dell’art. 2 comma 3 del D.M. 275 del 
30/10/2002

 

Si dichiara che questo prodotto è conforme 
alle normative vigenti e soddisfa i requisiti 
essenziali richiesti dalle direttive 
2004/108/CE, 2006/95/CE e 1999/05/CE

 

quando ad esso applicabili

 

 

Short Declaration of conformity

 

We declare this product is complying with the 
laws in force and meeting all the essential 
requirements as specified by the directives 
2004/108/CE, 2006/95/CE and 1999/05/CE

 

whenever these laws may be applied

 

 

FCC Information and Copyright

 

This equipment has been tested and found to comply with the limits of a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. There is no guarantee that interference 
will not occur in a particular installation.

 

 

The vendor makes no representations or warranties with respect to the contents here and 
specially disclaims any implied warranties of merchantability or fitness for any purpose. Further 
the vendor reserves the right to revise this publication and to make changes to the contents here 
without obligation to notify any party beforehand.

 

Duplication of this publication, in part or in whole, is not allowed without first obtaining the 
vendor’s approval in writing.

 

 

The content of this user’s manual is subject to be changed without notice and we will not be 
responsible for any mistakes found in this user’s manual. All the brand and product names are 
trademarks of their respective companies.

 

 

Summary of Contents for BIH11-AHB



















Reviews: