EN
77-2122-R13.1 (11/2015)
1 / 8
SERVICE MANUAL
WARNING — HIGH PRESSURE — WARNING
MAXIMUM WORKING PRESSURE UP TO 4000 POUNDS PER SQUARE INCH
• DO NOT POINT SPRAY GUN AT ANY PART OF THE HUMAN BODY
• FLUID UNDER HIGH PRESSURE CAN PENETRATE THE SKIN AND CAUSE SEVERE INTERNAL INJURY
• IN CASE OF INJURY OBTAIN MEDICAL ATTENTION IMMEDIATELY
• BE SURE TO REPORT NATURE OF INJURY AND TYPE OF FLUID OR SOLVENT TO THE DOCTOR
Be sure you understand ALL of the following instruc-
tions thoroughly BEFORE operating any part of the air-
less equipment system. CONSULT YOUR BINKS
REPRESENTATIVE TO CLEAR UP ANY ITEMS OF
INSTRUCTION YOU DO NOT UNDERSTAND.
1. UNDER NO circumstances should the spray gun be
carelessly handled nor its spray (even when the nozzle
is removed) directed at close proximity to any part of
the human body.
2. DO NOT operate airless spray gun with tip guard
housing removed or altered.
3.
NEVER clean, change, or remove the nozzle from the
spray gun without first doing the following:
a. Shut off pump and, in addition, unplug electrical
cord or turn off air supply.
b. Release fluid pressure in the entire system, from
pump or supply line to spray gun.
4. NEVER attempt to force the flow of liquid backward
through the gun (blowback) with your finger, hand, or
hand-held object pressed against the gun nozzle.
5. NEVER plug a hose leak with your finger, with adhe-
sive tape, or other “stop-gap” device.
6. NEVER operate the airless system with a defective
hose. ALWAYS replace the defective hose immediately.
For continuing safety, users are urged to:
a.
ALWAYS handle carefully all hose connections,
joints, and seating surfaces on the spray gun to pre-
vent damage.
b.
NEVER kink or bend the fluid hose into less than
a four inch radius.
c.
FREQUENTLY check the hose for kinks or abra-
sions. These may develop into a rupture.
d.
NEVER use standard hardware to modify the air-
less system. ALWAYS use Binks high pressure fit-
tings only.
7. The airless pump must be grounded before operating
the airless spray system.
Your new Binks 570 Automatic Airless Spray Gun has been
thoroughly tested before leaving the factory. No adjustments
are required before spray operations begin other than
installing the nozzle tip selected. The gun body has four
holes which allow the material body to be mounted in any
of four positions for convenient fluid hose hookup.
The following steps are recommended for obtaining best
results from your spray gun:
1. Install spray gun on gun mount and tighten the set
screw (9) securely. Note: The mounting hole is 1/2"
diameter.
2. Connect air hose to fitting (16). The gun is actuated
by air pressure from a 3-way valve. The valve pro-
vides air to trigger, shut-off, and exhausts air from the
gun. The gun should be limited to 200 cycles per min-
ute (maximum). Approximately 40 to 60 psi air pres-
sure is required to operate the spray gun; however, use
the minimum air pressure required.
3. Connect high pressure airless fluid hose to the gun
material body assembly (7) and tighten.
4. Remove tip guard assembly (4), nozzle tip, and gasket
(3) from spray gun (or remove Twist-Tip if used).
Turn on air supply to operate air valve to spray gun.
Turn on material supply very slowly and allow spray
gun to trigger a few times to purge any entrapped air
in fluid system.
5. Shut fluid supply and air supply OFF.
6. Replace gasket (3), nozzle tip, and tip guard assembly
(4) (or Twist-Tip) as per safety procedure described in
paragraph 3 above.
7. Turn air and fluid supply ON and check the spray pat-
tern for proper atomization.
8. The spray gun nozzle should be located at such a dis-
tance to the product where maximum fan pattern
width is evident. This is usually 8" to 14". The spray
pattern may be positioned either vertically or horizon-
tally by rotating nozzle tip (or the Twist-Tip).
continued on pg. 3
INSTALLATION AND OPERATING INSTRUCTIONS
NOTE
When the pattern is right, the pressure is right. Excessive fluid
pressure will only distort the spray pattern.
MODEL 570 AUTOMATIC
MASTIC AIRLESS SPRAY GUN
6700-0000-7 FOR PROFESSIONAL USE ONLY
