background image

INSTRUCTIONS

IMPORTANT SAFEGUARDS 

When using electrical equipment, basic safety precautions should always be followed including the following: 
1. 

READ AND FOLLOW ALL SAFETY INSTRUCTIONS 

2.   Disconnect power before performing work on electrical equipment.
3.   Do not use outdoors.
4.   Use caution when servicing batteries.  
5.   Equipment should be mounted in locations and at heights where unauthorized personnel will not readily subject it to
 tampering.
6.   The use of accessory equipment not recommended by Beghelli Canada Inc., may cause an unsafe condition, and
 

will void the unit’s warranty.

7.   Do not use this equipment for other than its intended purpose.

8.   Servicing of this equipment should be performed by qualified service personnel.

9.

  

SAVE THESE INSTRUCTIONS!

First, complete 

 Common Mounting Steps 

(page 2) before proceeding to mounting options shown below.

Bruno RM (BRU-RM)

Beghelli Canada Inc., 3900 14th Avenue, Markham, ON L3R 4R3 Tel: (905) 948-9500 Fax: (905) 948-8673

926000518

Page 1 of 7

Surface Ceiling Mounting, 

See page 3

T-Bar Mounting, 

See page 5

Surface End Mounting, 

See page 4

Surface Wall Mounting, 

See page 3

Ceiling Recessed Mounting, 

See page 6

Wall Recessed Mounting,

 

See page 6

08/03/2019

Summary of Contents for Bruno RM








Reviews: