Getting started and operation
Never touch the heating element!
Risk of burns!
a) Charging the product
Before you start using the product, the built-in rechargeable battery should be fully charged.
This takes about 20 to 45 minutes.
To charge the product, proceed as follows.
• Connect the provided micro SB cable to the micro USB port on the rear panel of the device.
Pay attention to the correct orientation when inserting the plug.
• Connect the normal USB plug type A to a USB port, e.g., of a USB power adapter.
• The charging process starts immediately. Meanwhile, the built-in LED lights blue.
• The LED lights up red out once the charging process is over.
b) Preparation of the product for operation
• In any case, remove the micro USB cable before you start using the product.
• Then close the upper cover.
If you are not using the product, the mechanical slide
switch should be always in the “Lock” position. Besi-
des, the cover should be closed.
• To start using the product, slide the switch from the “Lock” to
“Seal” position.
• Thus the product is ready for use.
c) Sealing a sack
• Hold firmly one end of the sack and set the handheld vacuum sealer in position (figure 1, ar-
row 1). At that, keep some distance to the device. Press on the cover and wait for 3 seconds
until the product preheats.
• Slide the handheld vacuum sealer along the sack to seal it (figure 2); always keep the cover
closed.
The speed of movement depends on the thickness of the bag. Sealing process for 20 cm
section should last about 5 to 7 seconds.
• As soon as you have finished on the right-hand side (figure 2), turn the sack around and place
the sealer onto the part that has not been sealed yet (figure 3, arrow 2).
• Preheat it again for 3 seconds and seal the remaining part of the sack.
Before you seal the sack completely, it is advisable to remove the air out of it.
• Now the sack is water and airtight sealed.
Whenever you stop operation, please remember to preheat the device for 3 seconds
thereafter.
The bag is either just sealed or cut and sealed depending on the thickness of the
bag and sealing speed. Thus, you can decide by yourself whether your bag should
or should not be cut.
If you are a left-hander, just seal the bag in a reverse direction. See figure above,
3 small figures shown bottom left.
• After you have finished using the product, slide the switch from the “Seal” to “Lock” position.
Operating instructions
Handheld vacuum sealer
Item no. 1434331
Intended use
The product serves for sealing or welding and cutting plastic bags or sacks. Bags and sacks
can be sealed up to a thickness of 0.3 mm. To find out which materials are supported, please
see the technical data of these instructions.
The power is supplied by a permanently integrated Li-ion rechargeable battery (non-replacea-
ble), which can be recharged through the supplied micro-USB cable from USB port or the USB
power adapter.
For safety and approval reasons (CE), you may not convert and/or alter the product. If you
use the product for purposes other than those described above, the product may be damaged.
Furthermore, improper use may cause risks such as short-circuits, fire, etc. Please read the
operating instructions carefully and do not discard them. If you pass the product on to a third
party, please hand over these operating instructions as well.
This product complies with the applicable national and European regulations. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package Contents
• Handheld vacuum sealer
• USB cable
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code. Follow the instructions on the website.
Safety Instructions
Please read the operating instructions carefully and pay particular attention to
the safety instructions. We do not assume liability for injuries/material damag-
es resulting from failure to observe the safety instructions and the information
in these operating instructions regarding the proper handling of the product.
Furthermore, in such cases, the warranty/guarantee will be null and void.
• The product is not a toy. Keep out of the reach of children and pets.
• Do not carelessly leave the packaging material lying around, since it could be-
come a dangerous plaything for children.
• Never touch the heating element! Risk of burns!
• If you will not be using the product, please make sure that the slide switch is
always in the “Lock” position and the cover closed.
• If you are not going to use the product for a long time (e.g., putting it into storage),
recharge the battery every 3 months at the latest to prevent deep discharge. In
the event of a deep discharge, the built-in Li-ion rechargeable battery will be per-
manently damaged!
• Protect the product from extreme temperatures, direct sunlight, strong vibrations
and combustible gases, vapours and solvents.
• Never expose the product to mechanical stress.
• The product must not get damp or wet, as this will destroy it. There is also risk of
fire and explosion from the integrated rechargeable battery.
• If safe operation is no longer possible, take the device out of service and secure
it against unintended use. Safe operation is no longer possible, if the product:
- has visible damage,
- no longer functions properly,
- has been stored under adverse ambient conditions for an extended period of
time or
- has been exposed to considerable strain during transport.
• Please handle the product carefully. The product can be damaged if crushed,
struck or dropped, even from a low height.
• If you have doubts about how the equipment should be operated or how to safely
connect it, consult a trained technician.
• Maintenance, adjustment and repair work may be carried out only by an expert or
a specialist workshop.
• If you have any questions that are not answered in these operating instructions,
please contact our technical customer service or another specialist.
