User Manual For
Digital Keypad Compact Safe
PARTS OF THE SAFE
A
B
C D
E
F
Parts of the Safe
A. Key Entry
B. Key Pad
C. Indicator Light
D. Reset Button
E. Battery Compartment
and Cover
F. Cable Slot
G. Mounting Holes
(located under the safe)
See reverse side for more information
1 2 3 4
OPENING THE SAFE WITH ACCESS KEY
1. Insert access key into key entry, turn clockwise to open,
partially lift lid of safe and remove access key by turning it
counter clockwise
2. Open safe by lifting the lid of the safe
NOTE
Store access keys in a secure place. NOT inside of safe
When calling for replacement or additional access keys have
the access key code number ready. The access key code is
etched in the key entry and on the access keys
BATTERIES
1. Locate the battery compartment and remove battery cover
2. Gently slide battery holder out of the compartment
3. Place 4, AA batteries and pay attention to the polarity of
each battery
4. Gently slide battery holder back into place
5. Replace battery cover
REPLACING BATTERIES
The red indicator light will start flashing and a continuous
beeping sound will be heard. This indicates that the batteries
are low.
1. Open safe by using the access key; turn clockwise
2. Repeat steps 1-5 of “Batteries” to replace batteries
3. Close safe and ensure that the safe is locked
NOTE
After replacing the batteries safe retains the last personal pin
codes saved
CREATING PERSONAL PIN CODES
For security purposes, change the factory default codes as soon
as possible and before placing valuables in the safe.
NOTE
Safe retains only two 3-8 digit pin codes
NOTE
1st default pin code is 1234
2nd default pin code is 1234
1st Personal Pin Code
1. With safe lid open, press and release the reset button. You
will hear 1 beep and indicator light will be consistently green
2. Enter in your 3 - 8 digit personal pin code on the key pad and
press and release the reset button
Successful Save
- You will hear 1 short and 1 long beep and green light flash
Unsuccessful Save
- You will hear a consistent beeping sound and red light
flashes 3 times
- Repeat steps 1 - 3
2nd Personal Pin Code
For security purposes you must change the 2nd pin code set
1. With safe lid open, press and release the reset button, wait 2
seconds and press and release the reset button again. You
will hear 2 beeps and indicator light will be consistently green
2. Follow step 2 in “1st Personal Pin Code”
NOTE
Be sure to write down these codes immediately and store in a
secure place
TESTING THE PERSONAL PIN CODES
1. With safe lid open, enter in 1st set of the personal pin code
on the key pad
Successful Save
- You will hear 1 short and 1 long beep and green light flash
- You will hear the safe unlock
Unsuccessful Save
- You will hear a consistent beeping sound and red light
flashes 3 times
- Repeat steps in “Creating Personal Pin Codes”
2. With safe lid open, enter in the 2nd set of the personal pin
code on the key pad.
See “Successful Save” and “Unsuccessful Save” above
3. Close safe and ensure that the safe is locked
OPENING SAFE WITH PERSONAL PIN CODES
1. Enter in either of the personal pin codes on the key pad
2. You will hear 1 short and 1 long beep and green light will flash
3. Open safe by lifting the lid of the safe
4. Close safe and ensure that the safe is locked
LOCK OUT
When the wrong personal pin code is entered 3 times the safe
will be in lock out mode. Lock out mode will last 30 seconds.
After 30 seconds try entering your personal pin code again.
3/13
BC287
WARNING
Avoid leaving safe door open and unattended; it will allow
unauthorized individuals to reprogram the safe, gaining full
access to the safe and the contents.
G
©2013 BARSKA® | Pomona, CA 91767, USA
(t) 888.666.6769 | (f) 909.445.8169 | www.barska.com
